Home › Drivetrain › K120 (CVT) › SHIFT LEVER › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461789 SHIFT LEVER A

K120 CVT  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

a.

Connect the shift lock control ECU connector.


b.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


c.

Connect the transmission control switch connector.


d.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


e.

Install the clip to the No. 1 console box duct.


f.
C370822N01
1.146,0.479 1.302,0.677 0.156,0.198 10 true 1 1.25,1.906 1.406,2.104 0.156,0.198 10 true 2 2.24,1.219 2.396,1.417 0.156,0.198 10 true 3 0.458,0.99 0.615,1.188 0.156,0.198 10 true 4

Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.


g.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C400603C02
1.646,1.198 1.844,1.594 1.844,1.594 2,1.594 false 1.313,1.344 1.583,1.594 0.271,0.25 10 false *a 2.042,1.49 2.333,1.708 0.292,0.219 10 false *b
*a Slide
*b Adjuster Case Cover


Slide the adjuster case cover in the direction shown by the arrow.


b.
C400817C02
1.115,4.052 1.323,4.052 1.323,4.052 1.708,3.354 true 0.875,2.75 1.146,2.75 1.146,2.75 1.75,3.073 false 0.875,0.604 1.146,0.604 1.146,0.604 1.75,0.927 false 1.083,1.875 1.292,1.875 1.292,1.875 1.677,1.177 true 1.854,1.302 2.156,1.542 0.302,0.24 10 false *a 0.906,1.781 1.219,1.938 0.313,0.156 10 false *b 0.948,3.958 1.24,4.188 0.292,0.229 10 false *b 0.708,0.5 0.958,0.74 0.25,0.24 10 false *c 0.708,2.646 0.958,2.885 0.25,0.24 10 false *c
*a Pull Out
*b Lock Piece
*c Adjuster Case


Using a precision screwdriver, pull out the lock piece of the adjuster case.


c.
C400818C01
0.448,1.208 0.625,1.208 0.625,1.208 1.729,1.49 true 2.188,1.26 2.896,2.208 2.896,2.208 2.208,3.479 true 0.49,3.177 0.708,3.177 0.708,3.177 1.385,3.438 true 0.26,1.115 0.573,1.271 0.313,0.156 10 false *a 2.01,0.365 2.323,0.521 0.313,0.156 10 false *b 2.948,2.104 3.26,2.26 0.313,0.156 10 false *c 0.281,3.104 0.594,3.26 0.313,0.156 10 false *a
*a Lock Nut
*b Push in
*c Stopper


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


d.
C453914C02
0.552,0.24 0.75,0.24 0.75,0.24 0.927,0.521 true 2.146,0.188 2.344,0.188 2.344,0.188 2.646,0.427 true 0.354,0.156 0.667,0.313 0.313,0.156 10 false *a 1.927,0.094 2.24,0.25 0.313,0.156 10 false *a
*a Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

After installation, check that the outer part of the stopper is as shown in the illustration.

·

Do not forcibly pull the transmission control cable assembly into the cabin.




e.
C453915

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the shift lever is in N.


·

Securely connect the end of the transmission control cable assembly to the transmission floor shift assembly.




f.
C453916C01
0.885,0.594 1.083,0.594 1.083,0.594 1.438,1.188 true 2.188,1.76 2.031,1.76 2.031,1.76 1.719,1.24 true 1.51,1.469 1.719,1.677 0.208,0.208 10 true *a 2.208,1.656 2.448,1.854 0.24,0.198 10 true *b 0.677,0.49 0.865,0.688 0.188,0.198 10 true *c
*a Push in
*b Lock Piece
*c Adjuster Case


Push in the lock piece of the adjuster case to lock it.

NOTICE:
·
C453917C01
0.406,2.073 0.563,2.073 0.563,2.073 0.74,2.594 true 2.115,0.542 2.458,0.542 false 0.198,1.958 0.385,2.156 0.188,0.198 10 true *1 1.979,0.438 2.219,0.667 0.24,0.229 10 false *a
*1 Transmission Control Cable Assembly
*a Lever Shaft


When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

·

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.




g.
C453918C01
1.156,1.698 1.333,1.698 1.333,1.698 1.656,1.25 true 1.469,4.375 1.646,4.375 1.646,4.375 1.823,3.677 true 0.938,4.25 1.115,4.25 1.115,4.25 1.625,3.667 true 0.938,1.604 1.135,1.802 0.198,0.198 10 true *a 0.74,4.146 0.917,4.344 0.177,0.198 10 true *a 1.26,4.281 1.448,4.479 0.188,0.198 10 true *b
*a Adjuster Case Cover
*b Lock Piece


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the transmission control cable assembly will not be able to lock, and reliable shift operation will not be possible.



Hide 33504F 4.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 33554C 5.INSTALL SHIFT LOCK RELEASE BUTTON COVER

a.
C370835

Engage the 2 claws and guide to install the shift lock release button cover to the rear upper console panel sub-assembly.


Hide 6.INSPECT SHIFT LEVER POSITION

Hide 7.ADJUST SHIFT LEVER POSITION