Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2021.02
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0326588 OIL COOLER A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 33493A 1.INSTALL TRANSMISSION OIL COOLER

a.
C418599N01
0.948,0.583 1.115,0.781 0.167,0.198 10 true A 1.01,1.875 1.177,2.073 0.167,0.198 10 true B 2.073,1.781 2.24,1.979 0.167,0.198 10 true C

Temporarily install the transmission oil cooler to the automatic transaxle case sub-assembly with the bolt (A).


b.

Install the bolt (B).

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


c.

Install the bolt (C).

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


d.

Fully tighten the bolt (A) to install the transmission oil cooler.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 16260 2.CONNECT WATER BY-PASS HOSE ASSEMBLY

a.

Connect the water by-pass hose assembly to the transmission oil cooler and slide the clip to secure it.

C419935C01
5.49,1 5.094,1.167 5.094,1.167 5.49,0.844 true 5.875,1.115 6.177,1.344 0.302,0.229 10 false *a 4.906,1.094 5.208,1.333 0.302,0.24 10 false *b 5.177,1.427 5.458,1.656 0.281,0.229 10 false *c 5.667,1.417 5.948,1.646 0.281,0.229 10 false *c
*a 2 to 7 mm (0.0787 to 0.276 in.) *b Paint Mark
*c 45° (Claw of Clip Location) - -


NOTICE:
·

Make sure to slide the water by-pass hose assembly until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the water by-pass hose assembly with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the clip are within the location shown in the illustration.




Hide 16261G 3.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the transmission oil cooler and slide the clip to secure it.

C419936C01
2.26,1.073 1.781,1.156 1.781,1.156 2.229,0.896 true 2.646,1.167 2.969,1.396 0.323,0.229 10 false *a 1.573,1.083 1.885,1.281 0.313,0.198 10 false *b 1.917,1.448 2.177,1.708 0.26,0.26 10 false *c 2.448,1.438 2.708,1.698 0.26,0.26 10 false *c
*a 2 to 7 mm (0.0787 to 0.276 in.) *b Paint Mark
*c 45° (Claw of Clip Location) - -


NOTICE:
·

Make sure to slide the No. 1 water by-pass hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the No. 1 water by-pass hose with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the clip are within the location shown in the illustration.




b.

Engage the 3 clamps to install the transmission breather clamp.


Hide 32907C 4.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

a.

w/o Air Cooled Oil Cooler:

i.

Install the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose to the No. 1 oil cooler tube sub-assembly without hose and slide the 4 clips to secure them.

C418580C01
5.313,1.896 4.969,1.896 false 2.708,2.531 2.823,2.385 2.823,2.385 2.969,2.385 false 3.49,3.333 3.49,2.927 false 3.802,1.177 3.958,1.177 3.958,1.177 4.427,1.813 false 3.198,1.573 3.354,1.573 3.354,1.573 3.49,1.76 false 3.031,1.479 3.344,1.688 0.313,0.208 10 false *1 3.438,3.344 3.688,3.594 0.25,0.25 10 false *2 3.646,1.094 3.927,1.313 0.281,0.219 10 false *3 3.01,2.271 3.26,2.479 0.25,0.208 10 false *4 5.354,1.792 5.688,2.031 0.333,0.24 10 false *5 1.625,2.458 1.885,2.667 0.26,0.208 10 false *a 6.313,2.938 6.573,3.167 0.26,0.229 10 false *b 1.656,0.24 1.938,0.49 0.281,0.25 10 false *c 1.208,2.781 1.479,3 0.271,0.219 10 false *d 1.844,0.927 2.104,1.135 0.26,0.208 10 false *a 5.052,0.938 5.313,1.146 0.26,0.208 10 false *a 5.073,2.958 5.333,3.167 0.26,0.208 10 false *a 5.219,0.219 5.5,0.469 0.281,0.25 10 false *c 5.385,2.281 5.667,2.531 0.281,0.25 10 false *c 1.021,2.063 1.302,2.313 0.281,0.25 10 false *c 0.875,3.51 1.146,3.729 0.271,0.219 10 false *d 0.219,0.615 0.469,0.823 0.25,0.208 10 false *b 0.552,0.521 0.802,0.729 0.25,0.208 10 false *b 6.26,0.656 6.51,0.865 0.25,0.208 10 false *b 6.563,0.49 6.813,0.698 0.25,0.208 10 false *b 6.135,3.229 6.396,3.458 0.26,0.229 10 false *b
*1 No. 1 Oil Cooler Tube Sub-assembly without Hose *2 Inlet No. 1 Oil Cooler Hose
*3 Inlet No. 2 Oil Cooler Hose *4 Outlet No. 1 Oil Cooler Hose
*5 Outlet No. 2 Oil Cooler Hose - -
*a 2 to 7 mm (0.0787 to 0.276 in.) *b 45° (Claw of Clip Location)
*c 0 to 3 mm (0 to 0.118 in.) *d 135° (Claw of Clip Location)


NOTICE:
·

Make sure to slide the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose until each contacts the hose stopper of the No. 1 oil cooler tube sub-assembly without hose.

·

Make sure that the claws of each clip are within the location shown in the illustration.





b.

w/ Air Cooled Oil Cooler:

i.

Install the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose and outlet No. 2 oil cooler hose to the No. 1 oil cooler tube sub-assembly without hose and slide the 3 clips to secure them.

C454114C01
5.313,1.896 4.969,1.896 false 3.49,3.333 3.49,2.927 false 3.802,1.177 3.958,1.177 3.958,1.177 4.427,1.813 false 3.198,1.573 3.354,1.573 3.354,1.573 3.49,1.76 false 3.031,1.479 3.344,1.688 0.313,0.208 10 false *1 3.438,3.344 3.688,3.594 0.25,0.25 10 false *2 3.646,1.094 3.927,1.313 0.281,0.219 10 false *3 5.354,1.792 5.688,2.031 0.333,0.24 10 false *4 1.625,2.188 1.885,2.396 0.26,0.208 10 false *a 6.313,2.938 6.573,3.167 0.26,0.229 10 false *b 1.208,2.542 1.479,2.76 0.271,0.219 10 false *d 5.052,0.938 5.313,1.146 0.26,0.208 10 false *a 5.073,2.958 5.333,3.167 0.26,0.208 10 false *a 5.219,0.219 5.5,0.469 0.281,0.25 10 false *c 5.385,2.281 5.667,2.531 0.281,0.25 10 false *c 1.021,1.792 1.302,2.042 0.281,0.25 10 false *c 0.865,3.229 1.135,3.448 0.271,0.219 10 false *d 6.26,0.656 6.51,0.865 0.25,0.208 10 false *b 6.563,0.49 6.813,0.698 0.25,0.208 10 false *b 6.135,3.229 6.396,3.458 0.26,0.229 10 false *b
*1 No. 1 Oil Cooler Tube Sub-assembly without Hose *2 Inlet No. 1 Oil Cooler Hose
*3 Inlet No. 2 Oil Cooler Hose *4 Outlet No. 2 Oil Cooler Hose
*a 2 to 7 mm (0.0787 to 0.276 in.) *b 45° (Claw of Clip Location)
*c 0 to 3 mm (0 to 0.118 in.) *d 135° (Claw of Clip Location)


NOTICE:
·

Make sure to slide the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose and outlet No. 2 oil cooler hose until each contacts the hose stopper of the No. 1 oil cooler tube sub-assembly without hose.

·

Make sure that the claws of each clip are within the location shown in the illustration.





c.
C370874C01
1.219,3.521 1.292,3.823 1.292,3.823 1.031,3.521 true 0.531,3.99 0.865,4.177 0.333,0.188 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 1.25,3.823 1.51,4.052 0.26,0.229 10 false *c 1.844,3.125 2.156,3.281 0.313,0.156 10 false *d 1.844,3.74 2.156,3.896 0.313,0.156 10 false *d
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d 45° (Claw of Clip Location)


Connect the outlet No. 2 oil cooler hose to the transmission oil cooler and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 2 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the outlet No. 2 oil cooler hose with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the clip are within the location shown in the illustration.




d.
C370875C01
1.063,3.552 1.396,3.865 1.396,3.865 1.302,3.552 true 0.573,4.042 0.927,4.281 0.354,0.24 10 false *a 0.51,2.885 0.823,3.042 0.313,0.156 10 false *b 1.365,3.875 1.698,4.073 0.333,0.198 10 false *c 1.802,3.115 2.115,3.271 0.313,0.156 10 false *d 1.813,3.802 2.125,3.958 0.313,0.156 10 false *d
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d 45° (Claw of Clip Location)


Connect the inlet No. 2 oil cooler hose to the transmission oil cooler and slide the clip to secure it.

NOTICE:
·

Make sure to slide the inlet No. 2 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the inlet No. 2 oil cooler hose with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the clip are within the location shown in the illustration.




e.

Temporarily install the No. 1 oil cooler tube sub-assembly without hose to the automatic transaxle case sub-assembly with the 2 bolts.


f.
C418581C01
0.875,1.229 1.083,1.229 1.083,1.229 1.323,0.677 true 0.531,1.146 0.865,1.365 0.333,0.219 10 true SST 2.073,0.938 2.365,1.156 0.292,0.219 10 true *a 0.688,0.708 0.917,0.906 0.229,0.198 10 true *b 2.198,0.063 2.417,0.271 0.219,0.208 10 true *c
*a Torque Wrench Fulcrum Length
*b Bolt (A)
*c Bolt (B)


Using SST, tighten the bolt (A).

SST
09961-00950  

Torque:
Specified tightening torque : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

7.0 N*m (71 kgf*cm, 62 in.*lbf)




g.

Tighten the bolt (B).

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 32941 5.CONNECT INLET NO. 1 OIL COOLER HOSE

a.
C418582C01
2.271,4.104 2.594,4.333 0.323,0.229 10 false *a 2.25,2.958 2.594,3.177 0.344,0.219 10 false *b
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)


Connect the inlet No. 1 oil cooler hose to the No. 1 oil cooler outlet tube sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to slide the inlet No. 1 oil cooler hose until it contacts the hose stopper of the No. 1 oil cooler outlet tube sub-assembly.



Hide 32942 6.CONNECT OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

a.
C418583C01
1.573,1.333 1.854,0.99 1.854,0.99 1.948,0.99 true 2.5,3.604 2.688,3.26 2.688,3.26 2.792,3.26 true 2.896,4.031 3.188,4.271 0.292,0.24 10 false *a 2.854,2.885 3.188,3.146 0.333,0.26 10 false *b 1.979,0.865 2.229,1.073 0.25,0.208 10 true *c 1.354,3.396 1.667,3.552 0.313,0.156 10 false *d 1.354,3.677 1.667,3.833 0.313,0.156 10 false *d 2.823,3.156 3.073,3.365 0.25,0.208 10 false *c
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark (Left Side of Vehicle)
*d 30° (Paint Mark Location)


Connect the outlet No. 1 oil cooler hose to the oil cooler union sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the oil cooler union sub-assembly.

·

Make sure that the paint mark of the outlet No. 1 oil cooler hose is within the location shown in the illustration.




Hide 32943 7.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (w/ Air Cooled Oil Cooler)

a.
C454111C01
2.354,2.896 2.646,3.115 0.292,0.219 10 false *a 2.604,3.74 2.875,3.99 0.271,0.25 10 false *b 1.031,3.24 1.323,3.458 0.292,0.219 10 false *c 0.625,3.354 0.917,3.573 0.292,0.219 10 false *c
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c 45° (Claw of Clip Location)


Connect the No. 1 transmission oil cooler hose to the No. 1 oil cooler tube sub-assembly without hose and slide the clip to secure it.

NOTICE:
·

Make sure to slide the No. 1 transmission oil cooler hose until it contacts the hose stopper of the No. 1 oil cooler tube sub-assembly without hose.




Hide 74404A 8.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 28800 10.INSTALL BATTERY

Hide 11.ADD ENGINE COOLANT

Hide 13.INSPECT FOR OIL LEAK

Hide 53737B 15.INSTALL FRONT FENDER APRON SEAL LH

Hide 16.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 51441 17.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 18.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 19.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 20.INSTALL FRONT WHEEL LH