Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2021.02
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319521 ENGINE ASSEMBLY A

A25A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>INSTALLATION

Hide 12304 2.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A428693N01
2.271,0.625 2.427,0.823 0.156,0.198 10 true A 1.365,0.396 1.521,0.594 0.156,0.198 10 true D 0.49,1.417 0.646,1.615 0.156,0.198 10 true C 3.25,2.115 3.406,2.313 0.156,0.198 10 true B

Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C), (D) and (A).

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Make sure that there is no gap between the engine mounting bracket sub-assembly LH and vehicle body before tightening the bolts.



Hide 12341 3.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A402194N01
1.438,1.865 1.594,2.063 0.156,0.198 10 true A 2.604,0.719 2.76,0.917 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A402193N01
1.042,1.698 1.198,1.896 0.156,0.198 10 true A 2.677,0.927 2.833,1.125 0.156,0.198 10 true B 2.333,0.135 2.49,0.333 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Engage the clamp.


c.

Connect the No. 1 bond cable to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


d.

Connect the bracket to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
A430356N01
0.708,1.146 0.865,1.344 0.156,0.198 10 true 1 2.646,0.271 2.802,0.469 0.156,0.198 10 true 2

Install the radiator reserve tank assembly with the bolt and nut in the order shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Engage the clamp.


g.

Connect the No. 6 water by-pass hose.


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 82121 7.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 19315 8.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 32101 9.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 11363A 12.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 12371A 14.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>INSTALLATION

Hide 12361A 15.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51100G 16.INSTALL FRONT FRAME ASSEMBLY

a.

Install the rear engine mounting insulator to the front frame assembly with the 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Install the front engine mounting insulator to the front engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 45319 18.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 16261G 21.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 32101A 23.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 11361J 24.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform inspection after repair after replacing the engine assembly.



a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.


c.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




e.
A402188C01
1.354,2.198 1.51,2.396 0.156,0.198 10 true A 1.333,2.427 1.49,2.625 0.156,0.198 10 true A 1.958,2.167 2.115,2.365 0.156,0.198 10 true A 1.969,2.385 2.125,2.583 0.156,0.198 10 true A 0.958,0.375 1.115,0.573 0.156,0.198 10 true B 2.302,0.365 2.458,0.563 0.156,0.198 10 true B 1.229,2.646 1.385,2.844 0.156,0.198 10 true C 2.073,2.656 2.229,2.854 0.156,0.198 10 true C 0.781,4.458 0.938,4.656 0.156,0.198 10 true D 2.521,4.448 2.677,4.646 0.156,0.198 10 true D 2.573,3.75 2.729,3.948 0.156,0.198 10 true E 0.719,3.771 0.875,3.969 0.156,0.198 10 true E
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.

Torque:
Bolt (A) : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Bolt (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)


f.

Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.

Torque:
Bolt (D) : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)
Bolt (E) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Nut : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)


g.

Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



h.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


i.

Install the body mounting plate with the 6 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


j.

Engage the clamp.


Hide 17410 27.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 45220 28.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 32943 29.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (w/ Air Cooled Oil Cooler)

Hide 32942 30.CONNECT OUTLET NO. 3 OIL COOLER HOSE (w/ Air Cooled Oil Cooler)

a.
A487332C01
2.5,3.604 2.688,3.26 2.688,3.26 2.792,3.26 true 2.896,4.031 3.188,4.271 0.292,0.24 10 false *a 2.854,2.885 3.188,3.146 0.333,0.26 10 false *b 1.354,3.396 1.667,3.552 0.313,0.156 10 false *d 1.354,3.677 1.667,3.833 0.313,0.156 10 false *d 2.823,3.156 3.073,3.365 0.25,0.208 10 false *c
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark (Left Side of Vehicle)
*d 30° (Paint Mark Location)


Connect the outlet No. 3 oil cooler hose to the No. 1 oil cooler tube sub-assembly without hose and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 3 oil cooler hose until it contacts the hose stopper of the No. 1 oil cooler tube sub-assembly without hose.

·

Make sure that the paint mark of the outlet No. 3 oil cooler hose is within the location shown in the illustration.




Hide 16281F 31.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Engage the clamp.


b.

Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 32.CONNECT WIRE HARNESS

a.
A402183N01
1.635,2.594 1.792,2.792 0.156,0.198 10 true A 0.729,0.833 0.885,1.031 0.156,0.198 10 true B 1.677,1.708 1.833,1.906 0.156,0.198 10 true C

Connect the wire harness to the vehicle body with the bolt.

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the earth wire to the automatic transaxle assembly with the bolt.

Torque:
Bolt (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.

Connect the wire harness to the positive (+) battery terminal with the nut.

Torque:
Nut (C) : 7.6 N*m (77 kgf*cm, 67 in.*lbf)


d.

Engage the 3 clamps.


e.

Engage the claw to install the wire harness to the engine room relay block and junction block assembly.


f.

Connect the 4 connectors to the engine room relay block and junction block assembly.


g.

Install the nut to the engine room relay block and junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Install the engine room relay block and junction block assembly cover to the engine room relay block and junction block assembly.


Hide 88711 33.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 34.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 16572D 35.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 36.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


b.

Connect the No. 1 radiator hose to the No. 1 radiator bracket with the clamp.


Hide 23901 37.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly.

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



b.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


Hide 87245 38.CONNECT INLET HEATER HOSE

a.
A403462C02
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 false 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.844 2.948,2 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and push them together until the inlet heater hose connector makes a "click" sound.


b.
A402657C03
1.365,1.115 1.688,0.49 1.688,0.49 1.917,0.49 false 1.969,0.406 2.281,0.563 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.


Hide 87246 39.CONNECT OUTLET HEATER HOSE

a.
A403463C02
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater hose connector and push them together until the outlet heater hose makes a "click" sound.


b.
A402654C02
2.26,1.521 2.073,1.521 2.073,1.521 1.771,1.188 false 2.323,1.438 2.563,1.635 0.24,0.198 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.


Hide 44773F 40.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the vacuum pump assembly and slide the clip to secure it.


Hide 23826 41.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.


Hide 33820B 42.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.
C378147C02
0.729,2.063 1.031,2.292 0.302,0.229 10 false *a 2.094,2.063 2.375,2.313 0.281,0.25 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



Hide 74404A 43.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly with the 3 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


b.

Engage the 4 clamps to the battery clamp sub-assembly.


Hide 46.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A402354C01
0.583,3.844 0.833,3.375 0.833,3.375 1,3.375 true 1.104,4.281 1.104,4.031 1.104,4.031 1.229,3.865 true 1.031,3.292 1.344,3.448 0.313,0.156 10 false *a 1.052,4.281 1.365,4.438 0.313,0.156 10 false *b 2.927,3.26 3.24,3.417 0.313,0.156 10 false *c 2.083,4.229 2.396,4.385 0.313,0.156 10 false *d 1.031,0.115 1.344,0.271 0.313,0.156 10 false *e 1.927,0.135 2.24,0.292 0.313,0.156 10 false *f
*a Protrusion
*b Cutout
*c Top
*d Front of Vehicle
*e Locked
*f Unlocked


Install the air cleaner assembly with air cleaner hose to the throttle body with motor assembly and unlock the hose clip to secure it as shown in the illustration.

NOTICE:

Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.



b.
A402355C01
0.844,1.26 0.948,1.083 0.948,1.083 1.063,1.083 true 0.75,0.844 1.063,1 0.313,0.156 10 false *a 0.104,1.323 0.417,1.479 0.313,0.156 10 false *b 0.188,1.104 0.5,1.26 0.313,0.156 10 false *c 0.188,1.542 0.5,1.698 0.313,0.156 10 false *c 1.094,0.99 1.406,1.146 0.313,0.156 10 false *d
*a Top
*b Front of Vehicle
*c 45°(Claw of Clip Location)
*d Paint Mark


Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



c.
A452080C02
2.781,3.49 2.563,3.49 true 2.354,3.865 2.135,3.865 true 1.438,3.938 1.219,3.938 true 2.844,3.385 3.156,3.583 0.313,0.198 10 true *a 2.438,3.75 2.75,3.948 0.313,0.198 10 true *a 0.969,3.844 1.188,4.063 0.219,0.219 10 true *a
*a Air Cleaner Support


Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports as shown in the illustration.

NOTICE:
·

Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports at the same time.

·

Check that the 3 pins are securely inserted into the 3 air cleaner supports.




d.

Engage the vacuum hose to the air cleaner hose.


e.

Engage the 3 wire harness clamps.


f.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 47.INSTALL INLET AIR CLEANER ASSEMBLY

a.
A402165N01
0.677,1.677 0.833,1.875 0.156,0.198 10 true 1 1.375,1.667 1.531,1.865 0.156,0.198 10 true 2

Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12601B 48.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A402166

Engage the 3 clips to install the No. 1 engine cover sub-assembly.


Hide 49.INSPECT VACUUM HOSES

a.

Inspect the vacuum hoses.

A486152


Hide 50.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 52.ADD ENGINE COOLANT

Hide 54.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 58.INSPECT FOR ENGINE OIL LEAK

Hide 64.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 52618 65.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Engage the 2 claws to install the front lower bumper absorber.


b.

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 52119A 66.INSTALL FRONT BUMPER COVER

Hide 53737B 67.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736 68.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 69.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

a.

Install the No. 2 engine under cover assembly with the 4 screws and 6 clips.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 70.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53852K 71.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

a.

Install the front wheel opening extension pad LH with the 3 screws.


Hide 53851M 72.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

a.

Install the front wheel opening extension pad RH with the 3 screws.


Hide 73.INSTALL FRONT WHEELS

Hide 74. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 75.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT