Refer to DTC P074512.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P074512
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P074514 | Pressure Control Solenoid "A" Circuit Short to Ground or Open | An open or short to ground is detected in the shift solenoid valve SL1 circuit for 1 second or more (1-trip detection logic). | ·
Transmission valve body assembly (Shift solenoid valve SL1) ·
Transmission wire ·
Harness and connector ·
TCM |
Comes on | DTC stored | SAE Code:
P0962 |
This DTC indicates an open or short to ground in the shift solenoid valve SL1 circuit. If there is an open or short to ground in the shift solenoid valve SL1 circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Perform the D Position Shift Test inspection in Road Test.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P074514.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P074512.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P074512
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C112 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SL1+) - 7 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 2 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| 7 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C112 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C111 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C111-38 (SL1+) - C111-37 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C111-38 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C111-37 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C111 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Disconnect the C112 transmission wire connector.
| *1 | Transmission Valve Body Assembly | *2 | Shift Solenoid Valve SL1 |
| *3 | Transmission Wire | - | - |
| *a | Shift Solenoid Valve Side | *b | Wire Harness Connector Side |
Disconnect the transmission wire connector from the shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (shift solenoid valve side) - 2 (SL1+) (wire harness connector side) | Always | Below 1 Ω |
| 2 (shift solenoid valve side) - 7 (SL1-) (wire harness connector side) | Always | Below 1 Ω |
| 1 (shift solenoid valve side) or 2 (SL1+) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| 2 (shift solenoid valve side) or 7 (SL1-) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transmission valve body assembly.
Click hereDrivetrain>K120 (CVT)>VALVE BODY ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION