The yaw rate and acceleration sensor is built into the airbag sensor assembly. The airbag sensor assembly sends yaw rate and acceleration sensor signals to the TCM via CAN communication. These signals are used for the neutral control. If a yaw rate and acceleration sensor circuit malfunction signal, yaw rate and acceleration sensor stuck signal or abnormal sensor output signal is received from the skid control ECU, a DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P158549 | Acceleration Sensor Circuit Internal Electronic Failure | Yaw rate and acceleration sensor circuit malfunction signal is received from the skid control ECU for 3 seconds or more (1-trip detection logic). | ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
CAN communication system ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) ·
TCM |
Does not come on | DTC stored | SAE Code:
P1585 |
| P158649 | Acceleration Sensor Circuit Range / Performance Internal Electronic Failure | Yaw rate and acceleration sensor stuck signal or abnormal sensor output signal is received from the skid control ECU for 3 seconds or more (1-trip detection logic). | ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
CAN communication system ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) ·
TCM |
Does not come on | DTC stored | SAE Code:
P1586 |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Drive the vehicle while accelerating and decelerating repeatedly for several minutes.
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P158549 or P158649.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P158504.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P158504
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
If any CAN communication system DTCs are output, perform troubleshooting for the CAN communication system first.
If any DTCs other than P158549 or P158649 are output, troubleshoot those DTCs first.
| Result | Proceed to |
|---|---|
| Only DTC P158549 or P158649 is output | A |
| DTC P158549 or P158649 and other DTCs are output | B |
A
B
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check the airbag sensor assembly installation condition.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The airbag sensor assembly is not tilted and its installation bolts are tightened to the specified torque, the airbag sensor assembly bracket is not deformed and there are no foreign objects under the airbag sensor assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K73 airbag sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K73-36 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K73-33 (E1) - Body ground | Always | Below 1 Ω |
| K73-32 (E2) - Body ground | Always | Below 1 Ω |
Connect the K73 airbag sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the airbag sensor assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Reinstall or replace the airbag sensor assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform Initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P158549 or P158649 is output | B |
A
B
Replace the brake actuator assembly.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Perform Initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P158549 or P158649 is output | B |
A
B
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION