Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461913 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P274912  Intermediate Shaft Speed Sensor "C" Circuit Short to Battery  P274914  Intermediate Shaft Speed Sensor "C" Circuit Short to Ground or Open  P274931  Intermediate Shaft Speed Sensor "C" No Signal  


DESCRIPTION

The transmission revolution sensor (NSS) detects the secondary pulley speed and sends it to the TCM.

The TCM determines the current gear ratio from the transmission revolution sensor (NSS) signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P274912 Intermediate Shaft Speed Sensor "C" Circuit Short to Battery The transmission revolution sensor (NSS) signal is normal but the transmission revolution sensor (NSS) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NSS)

·

TCM


Comes on DTC stored SAE Code:
P07CA
P274914 Intermediate Shaft Speed Sensor "C" Circuit Short to Ground or Open The transmission revolution sensor (NSS) signal is normal but the transmission revolution sensor (NSS) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NSS)

·

TCM


Comes on DTC stored SAE Code:
P07C9
P274931 Intermediate Shaft Speed Sensor "C" No Signal When the transmission revolution sensor (NOUT) signal indicates 350 rpm or more and the transmission revolution sensor (NT) signal indicates 780 rpm or more, the transmission revolution sensor (NSS) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NSS)

·

TCM


Comes on DTC stored SAE Code:
P2751

MONITOR DESCRIPTION

The TCM receives signals from the transmission revolution sensor (NSS) installed to the continuously variable transaxle and determines the secondary pulley speed in order to control the gear ratio.

If the TCM detects no signal from the transmission revolution sensor (NSS) even while the vehicle is being driven, it will determine that in the transmission revolution sensor (NSS) is malfunctioning, illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P274912, P274914 or P274931.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C318994E88
0.271,2.844 3.792,3.042 3.521,0.198 10 false Transmission Revolution Sensor (NSS) 5.979,3.042 6.5,3.333 0.521,0.292 10 false TCM 5.677,1.115 6.396,1.469 0.719,0.354 10 false NSSB 5.385,1.115 5.844,1.313 0.458,0.198 10 false 23 2.094,1.115 2.552,1.313 0.458,0.198 10 false 2 1.583,1.115 2.146,1.354 0.563,0.24 10 false NSSB 1.573,2.094 2.115,2.323 0.542,0.229 10 false NSSO 2.094,2.094 2.552,2.292 0.458,0.198 10 false 1 5.469,2.083 5.927,2.281 0.458,0.198 10 false 7 5.677,2.083 6.135,2.281 0.458,0.198 10 false NSSO 5.969,2.896 6.427,3.094 0.458,0.198 10 false C111 0.271,2.677 0.729,2.875 0.458,0.198 10 false C115 6.302,0.958 6.76,1.156 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (NSS SENSOR SPEED AND NSS SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NSS Sensor Speed Secondary pulley speed (NSS) Min.: 0 rpm
Max.: 65535 rpm
·

0 rpm: Vehicle stopped and shift lever in D

·

Equal to NO Sensor Speed: Vehicle being driven in belt mode


-
NSS Sensor Voltage Transmission revolution sensor (NSS) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Transmission > Data List
Tester Display
NSS Sensor Speed
NSS Sensor Voltage
50003 373 925,926

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

2.REPLACE TCM

B

3.INSPECT TRANSMISSION REVOLUTION SENSOR (NSS)
2.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION

3.INSPECT TRANSMISSION REVOLUTION SENSOR (NSS)
a.

Remove the transmission revolution sensor (NSS).

Click hereDrivetrain>K120 (CVT)>REVOLUTION SENSOR (NSS SENSOR)>REMOVAL


b.

Connect the battery to the transmission revolution sensor (NSS) as shown in the illustration.

C397726C03
1.448,1.833 1.615,1.417 true 2.083,1.833 1.917,1.417 true 4.083,1.104 4.333,1.354 true 4.625,1.354 4.875,1.604 true 5.854,0.917 6.167,1.073 0.313,0.156 10 false *1 5.125,0.573 5.438,0.729 0.313,0.156 10 false *2 1.208,0.656 1.521,0.813 0.313,0.156 10 false *a 4.646,1.823 4.958,1.979 0.313,0.156 10 false *b 3.781,2.229 4.094,2.385 0.313,0.156 10 false *c 1.25,1.854 1.708,2.052 0.458,0.198 10 false NSSB 1.927,1.854 2.385,2.052 0.458,0.198 10 false NSSO 3.969,1.021 4.125,1.219 0.156,0.198 10 false 2 4.917,1.552 5.073,1.75 0.156,0.198 10 false 1
*1 Battery *2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NSS))
*b Magnet
*c 5 mm or less - -



c.

Wave a magnet left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NSS) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnet during the inspection. The current will not change unless the magnet is moved as shown in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NSSO) - 2 (NSSB) Low signal 4 to 8 mA
1 (NSSO) - 2 (NSSB) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NSS) - TCM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NSS)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NSS) - TCM)
a.

Disconnect the C115 transmission revolution sensor (NSS) connector.


b.

Disconnect the C111 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-1 (NSSO) - C111-7 (NSSO) Always Below 1 Ω
C115-2 (NSSB) - C111-23 (NSSB) Always Below 1 Ω
C115-1 (NSSO) or C111-7 (NSSO) - Body ground and other terminals Always 10 kΩ or higher
C115-2 (NSSB) or C111-23 (NSSB) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C111 TCM connector.


e.

Connect the C115 transmission revolution sensor (NSS) connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NSS) - TCM)

5.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION