Using the current from the TCM, the shift solenoid valve SLU controls the lock-up clutch pressure, and performs lock-up and flex lock-up control.
The TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect mechanical malfunctions of the shift solenoid valve SLU, transmission valve body assembly and torque converter assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P275600 | Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance/Stuck Off | When the TCM commands lock-up ON, the difference between the engine speed (NE) and transmission revolution sensor (NT) signal is 250 rpm or more for 1 second or more (2-trip detection logic). | ·
Transmission valve body assembly (Shift solenoid valve SLU) ·
Continuously variable transaxle assembly ·
Torque converter assembly |
Comes on | DTC stored | SAE Code:
P2757 |
| P27567E | Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck On | When the TCM commands lock-up OFF, the difference between the engine speed (NE) and transmission revolution sensor (NT) signal is less than 25 rpm for 1 second or more (1-trip detection logic). | ·
Transmission valve body assembly (Shift solenoid valve SLU) ·
Continuously variable transaxle assembly ·
Torque converter assembly |
Comes on | DTC stored | SAE Code:
P2757 |
When performing lock-up control (ON/OFF) of the torque converter assembly, the TCM compares the transmission revolution sensor (NT) signal and engine speed (NE) signal to detect mechanical malfunctions in the shift solenoid valves SLU.
If the torque converter does not lock-up while a lock-up ON command is being sent, the TCM detects it as a mechanical malfunction of the shift solenoid valve SLU.
If the difference between the engine speed (NE) signal and transmission revolution sensor (NT) signal is outside of the threshold, the TCM detects the malfunction, illuminates the MIL and stores a DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P275600 or P27567E.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If any DTCs other than P275600 or P27567E are output, perform troubleshooting for those DTCs first.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
If DTC P275612 or P275614 is output, perform troubleshooting for that DTC first.
If DTCs P275612 and P275614 are not output but DTC P281F00 is output, perform troubleshooting for DTC P281F00 first.
| Result | Proceed to |
|---|---|
| Only DTC P275600 and/or P27567E is output | A |
| DTC P275600 and/or P27567E and P275612 are output | B |
| DTC P275600 and/or P27567E and P275614 are output | C |
| DTC P275600 and P281F00 are output | D |
| DTC P275600 and/or P27567E and DTCs other than P275612, P275614 and P281F00 are output | E |
A
B
C
D
E
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Disconnect the transmission wire connector from the shift solenoid valve SLU.
Click hereDrivetrain>K120 (CVT)>VALVE BODY ASSEMBLY>REMOVAL
| *1 | Transmission Valve Body Assembly | *2 | Shift Solenoid Valve SLU |
| *a | Component without harness connected
(Shift Solenoid Valve SLU) |
- | - |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve SLU connector. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the torque converter assembly.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Replace the transmission valve body assembly.
Click hereDrivetrain>K120 (CVT)>VALVE BODY ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION