Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461913 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P282814  Pressure Control Solenoid "K" Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P282812.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P282812

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P282814 Pressure Control Solenoid "K" Circuit Short to Ground or Open An open or short to ground is detected in the shift solenoid valve SLS circuit for 1 second or more (1-trip detection logic).
·

Transmission valve body assembly (Shift solenoid valve SLS)

·

Transmission wire

·

Harness and connector

·

TCM


Comes on DTC stored SAE Code:
P282F

MONITOR DESCRIPTION

This DTC indicates an open or short to ground in the shift solenoid valve SLS circuit. If there is an open or short to ground in the shift solenoid valve SLS circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P282814.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLS)
a.
C397724C05
1.583,1.521 0.698,1.104 true 1.583,1.76 0.708,1.958 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.365,1.875 0.979,2.073 0.615,0.198 10 false SLS- 0.323,1.021 0.938,1.219 0.615,0.198 10 false SLS+
*a Component without harness connected
(Transmission Wire)


Disconnect the C112 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
15 (SLS+) - 20 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
15 (SLS+) - Body ground and other terminals Always 10 kΩ or higher
20 (SLS-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the C112 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

4.INSPECT TRANSMISSION WIRE
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C111 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-4 (SLS+) - C111-3 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
C111-4 (SLS+) - Body ground and other terminals Always 10 kΩ or higher
C111-3 (SLS-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the C111 TCM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM)

3.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION

4.INSPECT TRANSMISSION WIRE
a.

Disconnect the C112 transmission wire connector.

C397732C01
3,2.75 3.75,2.75 true 4.792,2.813 5.542,3.063 true 4.792,3.427 5.542,3.26 true 5.448,1.313 5.698,0.896 true 6.229,1.313 5.979,0.896 true 1.104,0.135 1.417,0.292 0.313,0.156 10 false *1 3.802,2.677 4.115,2.833 0.313,0.156 10 false *2 4.771,0.146 5.083,0.302 0.313,0.156 10 false *3 5.771,0.24 6.083,0.396 0.313,0.156 10 false *a 5.75,1.938 6.063,2.094 0.313,0.156 10 false *b 4.406,2.719 5.021,2.917 0.615,0.198 10 false SLS+ 4.438,3.344 5.052,3.542 0.615,0.198 10 false SLS- 5.344,1.25 5.5,1.448 0.156,0.198 10 false 1 6.271,1.25 6.427,1.448 0.156,0.198 10 false 2
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SLS
*3 Transmission Wire - -
*a Shift Solenoid Valve Side *b Wire Harness Connector Side



b.

Disconnect the transmission wire connector from the shift solenoid valve SLS.

Click hereDrivetrain>K120 (CVT)>VALVE BODY ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (shift solenoid valve side) - 15 (SLS+) (wire harness connector side) Always Below 1 Ω
2 (shift solenoid valve side) - 20 (SLS-) (wire harness connector side) Always Below 1 Ω
1 (shift solenoid valve side) or 15 (SLS+) (wire harness connector side) - All other terminals Always 10 kΩ or higher
2 (shift solenoid valve side) or 20 (SLS-) (wire harness connector side) - All other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSMISSION VALVE BODY ASSEMBLY

NG

REPLACE TRANSMISSION WIRE

5.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
a.

Replace the transmission valve body assembly.

Click hereDrivetrain>K120 (CVT)>VALVE BODY ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION