Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461913 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM U

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
Total Distance Traveled - Unit Unit for Total Distance Traveled km or mile - -
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

The vehicle speed is detected using the wheel speed sensors.

-

There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.



Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
750 to 850 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Calculate Load Load calculated by ECM Min.: 0%
Max.: 100%
-
·

This is the engine load calculated based on the estimated intake pressure.

·

Calculate Load = Estimated intake pressure / maximum intake pressure x 100 (%)

(For example, when the estimated intake pressure is the same as atmospheric pressure, Calculate Load is 100%.)


Coolant Temperature Coolant temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
HINT:
·

After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.

·

Check if the engine overheats if the value indicated is higher than 135°C (275°F).



Intake Air Temperature Intake air temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
Equivalent to temperature at location of mass air flow meter sub-assembly
HINT:
·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or higher than 128°C (262°F), the sensor circuit is open or shorted.



Ambient Temperature Ambient temperature Min.: -40°C (-40°F)
Max.: 215 °C (419 °F)
Equivalent to ambient air temperature
HINT:
·

After a long soak, the engine coolant temperature, engine oil temperature, intake air temperature and ambient air temperature are approximately equal.



Engine Run Time Engine run time Min.: 0 sec.
Max.: 65535 sec.
Time elapsed since engine started. This is the time elapsed since the engine was started.
HINT:

The time is counted only while the engine is running.


Battery Voltage Battery voltage Min.: 0 V
Max.: 65.5 V
11 to 14 V: Engine idling If 11 V or less, characteristics of some electrical components may change.
Glow Indicator Supported Glow indicator supported Unsupp or Supp - -
Throttle Position Sensor No.1 Voltage % Absolute throttle position sensor (No. 1) Min.: 0%
Max.: 100%
·

10 to 22%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed (engine running)


The No. 1 throttle position sensor output is converted using 5 V = 100%.
HINT:

If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.


Shift SW Status (Neutral) Supported Status of shift switch (neutral) supported Unsupp or Supp Unsupp -
Stop Light SW Stop light switch assembly status OFF or ON
·

OFF: Brake pedal released

·

ON: Brake pedal depressed


-
Complete Parts Monitor Comprehensive component monitor Not Avl or Avail -
·

*2


Complete Parts Monitor Result Comprehensive component monitor Compl or Incmpl -
·

*2


Ignition Monitor Ignition monitor Spark Ignition or Compression Ignition - -
Fuel System Monitor Fuel system monitor Not Avl or Avail -
·

*2


Fuel System Monitor Result Fuel system monitor Compl or Incmpl -
·

*2


Misfire Monitor Misfire monitor Not Avl or Avail -
·

*2


Misfire Monitor Result Misfire monitor Compl or Incmpl -
·

*2


EGR/VVT Monitor EGR/VVT monitor Not Avl or Avail -
·

*2


EGR/VVT Monitor Result EGR/VVT monitor Compl or Incmpl -
·

*2


A/F (O2) Sensor Heater Monitor O2S (A/FS) heater monitor Not Avl or Avail -
·

*2


A/F (O2) Sensor Heater Monitor Result O2S (A/FS) heater monitor Compl or Incmpl -
·

*2


A/F (O2) Sensor Monitor O2S (A/FS) monitor Not Avl or Avail -
·

*2


A/F (O2) Sensor Monitor Result O2S (A/FS) monitor Compl or Incmpl -
·

*2


Secondary Air Injection System Monitor Secondary air injection system monitor Not Avl or Avail -
·

*2


Secondary Air Injection System Monitor Result Secondary air injection system monitor Compl or Incmpl -
·

*2


EVAP Monitor EVAP monitor Not Avl or Avail -
·

*2


EVAP Monitor Result EVAP monitor Compl or Incmpl -
·

*2


Heated Catalyst Monitor Heated catalyst monitor Not Avl or Avail -
·

*2


Heated Catalyst Monitor Result Heated catalyst monitor Compl or Incmpl -
·

*2


Catalyst Monitor Catalyst monitor Not Avl or Avail -
·

*2


Catalyst Monitor Result Catalyst monitor Compl or Incmpl -
·

*2


TC Terminal TC terminal status ON or OFF OFF -
MIL MIL status ON or OFF OFF -
MIL ON Run Distance MIL ON run distance Min.: 0 km (0 mile)
Max.: 65535 km (40723 miles)
Actual distance driven since DTC detected -
Running Time from MIL ON Running time from MIL on Min.: 0 min.
Max.: 65535 min.
Actual running time since MIL was illuminated -
Time after DTC Cleared Time after DTC cleared Min.: 0 min.
Max.: 65535 min.
Actual time elapsed since DTCs were cleared This is the time elapsed since DTCs were cleared (or after the vehicle left the factory). Time elapsed when the ignition switch is turned off is not counted.
Distance from DTC Cleared Distance driven after DTCs cleared Min.: 0 km (0 mile)
Max.: 65535 km (40723 miles)
Actual distance driven since DTCs cleared This is the distance driven since DTCs were cleared (or after the vehicle left the factory).
Warmup Cycle Cleared DTC Warmup cycles after DTCs cleared Min.: 0
Max.: 255
-
·

This is the number of times the engine was warmed up*1 after DTCs were cleared (or after the vehicle left the factory).


OBD Requirements OBD requirement - - -
Number of Emission DTC Emissions-related DTCs stored Min.: 0
Max.: 127
- -
Accel Position from EFI Accelerator pedal position Min.: 0%
Max.: 127.5%
Actual accelerator pedal position -
NSS Sensor Speed Secondary pulley speed (NSS) Min.: 0 rpm
Max.: 65535 rpm
·

0 rpm: Vehicle stopped and shift lever in D

·

Equal to NO Sensor Speed: Vehicle being driven in belt mode


-
NSS Sensor Voltage Transmission revolution sensor (NSS) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
NO Sensor Speed Output shaft speed (NOUT) Min.: 0 rpm
Max.: 65535 rpm
·

0 rpm: Vehicle stopped

·

Equal to NSS Sensor Speed: Vehicle being driven in belt mode


-
NO Sensor Voltage Transmission revolution sensor (NOUT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
NT Sensor Speed Input turbine speed (NT) Min.: 0 rpm
Max.: 65535 rpm
·

Equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in R


-
NC1 Sensor Speed Intermediate shaft (C1 clutch) speed (NC1) Min.: 0 rpm
Max.: 65535 rpm
·

0 rpm: Vehicle stopped and synchronizer engaged

·

Equal to NT Sensor Speed: Vehicle being driven in gear mode


-
NC1 Sensor Voltage Transmission revolution sensor (NC1) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi): D position stall test

·

1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi): R position stall test


-
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*3.


Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*3.


Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*3.


Shift SW Status (N,P Range) Park/neutral position switch assembly status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*3.


Shift SW Status (N,P Range) Supported Status of park/neutral position switch (N or P) supported Unsupp or Supp Supp -
Sport Shift Up SW Sport shift up switch status OFF or ON
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sport Shift Down SW Sport shift down switch status OFF or ON
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-
Shift SW Status (S Range) Transmission control switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in D

·

ON: Shift lever in D


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*3.


A/T Oil Temperature No.1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
or Invalid Value
·

Approximately 100°C (212°F): After stall speed test

·

Equal to ambient temperature: After cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate Estimated value of CVT fluid thermal degradation Min.: 0
Max.: 65535
- If 50000 or more is displayed, thermal degradation of the CVT fluid is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the CVT fluid.
CVT Oil Press Calibration CVT Oil Pressure Calibration status Incmp or Compl Compl -
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Acceleration Sensor Voltage Converted output voltage of yaw rate and acceleration sensor Min.: 0.000 V
Max.: 79.999 V
·

2.31 V to 2.69 V: Vehicle on level ground

·

1.88 V to 2.5 V: Decelerating

·

2.5 V to 3.11 V: Accelerating

·

1.87 V: G sensor malfunction

·

1.87 V: Communication malfunction


-
Synchronize Stroke Sensor Position Position of synchronizer Min.: 0.000 mm
Max.: 255.996 mm
·

0.000 to 1.573 mm (0 to 0.062 in.): Synchronizer not engaged

·

9.139 to 11.798 mm (0.360 to 0.464 in.): Synchronizer engaged


-
Synchronize Stroke Sensor Voltage Shift stroke sensor voltage Min.: 0.000 V
Max.: 4.999 V
·

3.587 to 4.429 V: Synchronizer not engaged

·

0.622 to 1.393 V: Synchronizer engaged


-
Status of Synchronize Synchronizer status OFF or ON
·

OFF: Synchronizer not engaged

·

ON: Synchronizer engaged


-
Lock Up Status Lock-up OFF, ON or Invalid Value
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
CVT Shift Status Ratio TCM gear ratio command Min.: 0
Max.: 15.999
Same as actual gear ratio -
Shift Mode Shift mode status Gear Mode or Belt Mode - -
Solenoid (SLU) Shift solenoid valve SLU status OFF or ON
·

ON: Shift solenoid valve SLU operating

·

OFF: Shift solenoid valve SLU not operating


-
Solenoid (SLS) High/Low Shift solenoid valve SLS status OFF or ON
·

ON: After engine start

·

OFF: Ignition switch ON


-
Solenoid (SLS) MAX/MIN Shift solenoid valve SLS status OFF or ON
·

ON: After engine start

·

OFF: Ignition switch ON


-
Solenoid (SLP) Shift solenoid valve SLP status OFF or ON
·

ON: Shift solenoid valve SLP operating

·

OFF: Shift solenoid valve SLP not operating


-
Solenoid (SLG) Shift solenoid valve SLG status OFF or ON
·

ON: Shift solenoid valve SLG operating

·

OFF: Shift solenoid valve SLG not operating


-
Solenoid (SL1) Shift solenoid valve SL1 status OFF or ON
·

ON: Shift solenoid valve SL1 operating

·

OFF: Shift solenoid valve SL1 not operating


-
Solenoid (SL2) Shift solenoid valve SL2 status OFF or ON
·

ON: Shift solenoid valve SL2 operating

·

OFF: Shift solenoid valve SL2 not operating


-
Acceleration Sensor Calibration Deceleration sensor zero point calibration status Incomplete or Complete Complete -
Acceleration Sensor Learn Value Yaw rate and acceleration sensor learned value voltage Min.: 0.000 V
Max.: 79.998 V
2.31 to 2.69 V: Deceleration Sensor Zero Point Calibration complete -
HINT:
·

*1: An engine warmup is defined as the engine coolant temperature rising 20°C (68°F) or more and reaching a temperature of 70°C (158°F) or more after the engine is started.

·

*2:

-

Avail: The monitor is available on the vehicle.

-

Not Avl: The monitor is not available on the vehicle.

-

Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or cable is disconnected from the negative (-) battery terminal.

-

Monitor result (mode 06): The last judgment result is output. This is not cleared when the ignition switch is turned off, but is cleared when DTCs are cleared.






ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal Turn on and off TC and TE1 (CG) connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P


Activate the Lock Up Solenoid Operates the lock-up ON or OFF Can be used to check lock-up operation.
Perform "Activate the Lock Up Solenoid" while monitoring "Engine Speed" and "NT Sensor Speed".
(Vehicle Condition)

Vehicle speed of 40 km/h (25 mph) or more


Activate the Solenoid (SLU) Operates the shift solenoid valve SLU ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N


Activate the Solenoid (SLS) High/Low Operates the shift solenoid valve SLS High or Low
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N


Activate the Solenoid (SLS) MAX/MIN Operates the shift solenoid valve SLS MIN or MAX
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N


Activate the Solenoid (SLP) Operates the shift solenoid valve SLP ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N


Active the Synchronize Operates the synchronizer ON or OFF
HINT:

If the value of Data List item Status of Synchronize is "ON", this Active Test cannot be changed to "ON". Additionally, if the value is "OFF", this Active Test cannot be changed to "OFF".


(Vehicle Condition)

Ignition switch ON, engine running, stop light switch assembly ON, shift lever in P and CVT fluid temperature between 20°C (68°F) and 100°C (212°F)


Control the Shift Mode Changes the shift mode GEAR: Gear Mode
LOW: Belt Mode (Low)
MIDDLE: Belt Mode (Middle)
HIGH: Belt Mode (High)
HINT:

Perform "Control the Shift Mode" while monitoring "CVT Shift Status Ratio" and "Shift Mode" to confirm actual shift mode.


(Vehicle Condition)

Vehicle speed between 20 km/h (10.8 mph) and 45 km/h (24.3 mph) and CVT fluid temperature -20°C (-4 °F) or more


Activate the Solenoid (SLG) Operates the shift solenoid valve SLG ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N


Activate the Solenoid (SL1) Operates the shift solenoid valve SL1 ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N


Activate the Solenoid (SL2) Operates the shift solenoid valve SL2 ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P or N