Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Parking Support Brake System) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0462611 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Parking Support Brake System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Parking Support Brake System)  No. 1 Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E429359E09
5.563,0.469 6.198,0.75 0.635,0.281 10 false CBZ 5.344,0.385 5.708,0.552 0.365,0.167 10 false 9 5.563,1.271 5.865,1.531 0.302,0.26 10 false EF 5.365,1.729 5.917,2.052 0.552,0.323 10 false R39 1.063,1.594 1.667,1.917 0.604,0.323 10 false K74 1.073,1.771 2.625,2.24 1.552,0.469 10 false No. 1 Clearance Warning Buzzer 5.365,1.885 6.906,2.469 1.542,0.583 10 false Clearance Warning ECU Assembly 5.313,1.188 5.656,1.354 0.344,0.167 10 false 8 2.063,0.406 2.167,0.573 0.104,0.167 10 false 1 2.063,1.188 2.167,1.354 0.104,0.167 10 false 2 1.781,1.281 2.063,1.448 0.281,0.167 10 false Z- 1.771,0.49 2.052,0.656 0.281,0.167 10 false Z+

CAUTION / NOTICE / HINT

NOTICE:

Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Parking Support Brake System)>CALIBRATION


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Warning / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Buzzer No. 1 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the ignition switch is ON
Body Electrical > Clearance Warning > Active Test
Tester Display
Front Buzzer
50004 438 1
OK:

The No. 1 clearance warning buzzer sounds.


Result:
Proceed to
OK
NG




OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the R39 clearance warning ECU assembly connector.


b.

Disconnect the K74 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-9 (CBZ) - K74-1 (Z+) Always Below 1 Ω
R39-8 (EF) - K74-2 (Z-) Always Below 1 Ω
R39-9 (CBZ) or K74-1 (Z+) - Body ground Always 10 kΩ or higher
R39-8 (EF) or K74-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER (for LHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Warning / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the ignition switch is ON
Body Electrical > Clearance Warning > Active Test
Tester Display
Front Buzzer
50004 438 1
OK:

The No. 1 clearance warning buzzer sounds.


Result:
Proceed to
OK
NG




OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG