Home › Engine / Hybrid System › M20A-FKS (FUEL) › FUEL PUMP (for High Pressure) › from 2021.02
RM33A0E _51 Engine / Hybrid System _098628 M20A-FKS FUEL _0462960 FUEL PUMP(for High Pressure) A

M20A-FKS FUEL  FUEL PUMP(for High Pressure)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23100X 1.TEMPORARILY INSTALL FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Turn the crankshaft pulley until the flat of the camshaft faces the fuel pump lifter assembly.

A444650C01
0.5,1.917 6.667,3.75 6.167,1.833 3.542,3.75 3.542,1.917 false 3.583,1 3.917,0.417 3.917,0.417 4.083,0.417 true 1.635,2.146 1.802,2.146 false 2.927,2.146 3.094,2.146 false 4.802,2.146 4.969,2.146 false 6.083,2.146 6.25,2.146 false 1.583,2.667 1.75,2.667 false 2.875,2.563 3.042,2.563 false 4.76,2.823 4.927,2.823 false 6.063,2.708 6.229,2.708 false 1.667,3.5 1.833,3.5 false 3.031,3.26 3.198,3.26 false 4.833,3.49 5,3.49 false 6.208,3.271 6.375,3.271 false 0.583,1.979 0.958,2.219 0.375,0.24 12 false *A 3.604,1.969 3.979,2.208 0.375,0.24 12 false *B 1.885,2.052 2.198,2.25 0.313,0.198 10 false *1 3.177,2.063 3.49,2.26 0.313,0.198 10 false *1 5.042,2.063 5.354,2.26 0.313,0.198 10 false *1 6.323,2.063 6.635,2.26 0.313,0.198 10 false *1 1.823,2.583 2.135,2.781 0.313,0.198 10 false *2 3.115,2.479 3.427,2.677 0.313,0.198 10 false *2 5,2.74 5.313,2.938 0.313,0.198 10 false *2 6.302,2.625 6.615,2.823 0.313,0.198 10 false *2 1.906,3.417 2.219,3.615 0.313,0.198 10 false *3 3.281,3.177 3.594,3.375 0.313,0.198 10 false *3 5.073,3.406 5.385,3.604 0.313,0.198 10 false *3 6.458,3.188 6.771,3.385 0.313,0.198 10 false *3 1.25,1.99 1.563,2.188 0.313,0.198 10 false *a 4.427,2.01 4.74,2.208 0.313,0.198 10 false *a 2.542,2.01 2.854,2.208 0.313,0.198 10 false *b 5.719,2 6.031,2.198 0.313,0.198 10 false *b 4.167,0.344 4.354,0.531 0.188,0.188 10 true *3
*A for Type A *B for Type B
*1 Fuel Pump Assembly *2 Fuel Pump Lifter Assembly
*3 Camshaft - -
*a Correct *b Incorrect


HINT:

This prevents the camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump assembly.



b.
A444651C01
0.167,2.583 3.25,4.417 3.083,1.833 0.969,0.365 1.135,0.365 1.135,0.365 1.542,1.104 true 0.615,2.25 0.615,1.542 true 1.573,2.281 1.573,1.573 true 0.479,4.104 0.646,4.104 0.646,4.104 0.875,3.635 true 1.698,4.417 1.698,2.583 false 2.094,4.094 2.26,4.094 2.26,4.094 2.49,3.625 true 0.531,2.302 0.76,2.479 0.229,0.177 10 true *1 1.51,2.313 1.708,2.49 0.198,0.177 10 true *2 0.74,0.281 0.938,0.479 0.198,0.198 10 true *a 0.271,4.042 0.594,4.26 0.323,0.219 10 false *b 1.875,4.01 2.198,4.229 0.323,0.219 10 false *b 0.25,2.635 0.563,2.885 0.313,0.25 12 false *A 1.76,2.646 2.073,2.896 0.313,0.25 12 false *B
*A for Type A
*B for Type B
*1 Cylinder Head Cover Sub-assembly
*2 Fuel Pump Spacer Gasket
*a Pump Drive Cam (Engine Oil Application Area)
*b Fuel Pump Lifter Assembly (Engine Oil Application Area)


Apply 30 cc (1.8 cu. in.) of engine oil to the pump drive cam.


c.

Apply engine oil to the fuel pump lifter assembly.


d.

Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly.


e.
A444652C01
1.281,0.781 1.594,0.781 true 1.927,0.781 2.24,0.781 true 1.313,1.083 1.448,1.083 1.448,1.083 1.708,1.406 true 1.927,1.375 2.24,1.156 2.24,1.156 2.365,1.156 true 1.292,3.115 1.604,3.115 true 1.927,3.125 2.24,3.125 true 1.313,3.417 1.448,3.417 1.448,3.417 1.708,3.74 true 1.938,3.677 2.25,3.458 2.25,3.458 2.375,3.458 true 0.042,0.208 0.292,0.406 0.25,0.198 12 true *A 0.042,2.521 0.292,2.729 0.25,0.208 12 true *B 1.073,0.688 1.26,0.885 0.188,0.198 10 true *a 1.073,1 1.281,1.177 0.208,0.177 10 true *b 2.448,1.073 2.635,1.26 0.188,0.188 10 true *d 2.281,0.698 2.479,0.875 0.198,0.177 10 true *c 1.073,3.021 1.26,3.219 0.188,0.198 10 true *a 2.292,3.042 2.49,3.219 0.198,0.177 10 true *c 1.063,3.323 1.271,3.5 0.208,0.177 10 true *b 2.427,3.375 2.615,3.563 0.188,0.188 10 true *d
*A for Type A
*B for Type B
*a Fuel Pump Lifter Assembly (Engine Oil Application Area)
*b Fuel Pump Lifter Guide (Engine Oil Application Area)
*c Stopper Key
*d Key Groove


Apply engine oil to the inside of the fuel pump lifter guide and the outside of the fuel pump lifter assembly.


f.

Set the fuel pump lifter assembly on the fuel pump lifter guide as shown in the illustration.

HINT:

Align the stopper key of the fuel pump lifter assembly with the key groove of the fuel pump lifter guide.



g.

Apply engine oil to a new O-ring and install it to the fuel pump assembly.

NOTICE:

Do not damage the O-ring.



h.
A444653C01
2.135,0.563 2.448,0.563 false 2.198,1.656 2.51,1.656 false 2.531,0.479 2.802,0.708 0.271,0.229 10 false *1 2.604,1.594 2.885,1.802 0.281,0.208 10 false *2
*1 Fuel Pump Assembly
*2 Fuel Pump Flange


Set the fuel pump flange and fuel pump assembly on the cylinder head cover sub-assembly as shown in the illustration.


i.

Temporarily install the fuel pump assembly with the 2 bolts, leaving some allowance for left and right movement.


Hide 23801P 2.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

NOTICE:

Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.


a.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel delivery pipe and tighten the union nut by hand.


b.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.


c.

Temporarily install the bolt.


Hide 23100X 3.INSTALL FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY

a.

Tighten the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


b.

Connect the fuel pump assembly connector.


Hide 23801P 4.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A481893C01
2.781,2.802 2.781,2.625 2.781,2.625 2.927,2.625 false 3.01,2.542 3.271,2.781 0.26,0.24 10 false *a 1.677,2.427 1.979,2.615 0.302,0.188 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Using an 8 mm socket wrench, tighten the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the ignition coil assembly connector.


Hide 23910A 5.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 10.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION