Home › Engine / Hybrid System › M20A-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2021.02
RM33A0E _51 Engine / Hybrid System _099290 M20A-FKS INTAKE / EXHAUST _0463507 INTAKE MANIFOLD A

M20A-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 17177 1.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 17111 2.INSTALL INTAKE MANIFOLD

a.

w/o Stud Bolt:

i.
A426164N01
2.958,0.188 3.083,0.354 0.125,0.167 10 true 5 0.125,0.188 0.25,0.354 0.125,0.167 10 true 4 2.208,0.021 2.333,0.188 0.125,0.167 10 true 3 0.885,0.01 1.01,0.177 0.125,0.167 10 true 2 1.573,0.052 1.698,0.219 0.125,0.167 10 true 1

Temporarily install the intake manifold to the cylinder head sub-assembly with the 5 bolts.


ii.

Tighten the 5 bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



b.

w/ Stud Bolt:

i.
A433671

Temporarily install the intake manifold to the cylinder head sub-assembly.


ii.

Using an E8 "TORX" socket wrench, install the 2 stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


iii.
A433670N01
1.667,0.979 1.823,1.177 0.156,0.198 10 true 1 1.146,0.854 1.292,1.042 0.146,0.188 10 true 2 2.208,0.875 2.354,1.063 0.146,0.188 10 true 3 0.594,0.979 0.74,1.167 0.146,0.188 10 true 4 2.729,0.948 2.875,1.135 0.146,0.188 10 true 5

Temporarily install the 3 bolts and 2 nuts.


iv.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



Hide 23827D 3.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the intake manifold.


Hide 17138B 4.INSTALL INTAKE MANIFOLD STAY

a.
A426160N01
1.885,1.729 2.01,1.896 0.125,0.167 10 true B 1.302,1.625 1.427,1.792 0.125,0.167 10 true A

Engage the guide to install the intake manifold stay.


b.

Install the bolt (B).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Using an 8 mm socket wrench, install the bolt (A).

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16279 5.CONNECT NO. 3 WATER BY-PASS PIPE

a.

Using an 8 mm socket wrench, connect the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 6.CONNECT ENGINE WIRE

a.

Engage the wire harness clamp to connect the engine wire.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the 2 wire harness clamps to connect the engine wire.


d.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Connect the 2 connectors.


Hide 25601 7.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 22030 9.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Using an 8 mm socket wrench, install the throttle body with motor assembly to the intake manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the throttle body with motor assembly connector.


Hide 10.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 12601B 11.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 13.INSTALL COOL AIR INTAKE DUCT SEAL