| *A | for Type A |
| *B | for Type B |
| *a | Tube |
Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.
When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.
83320
1.REMOVE FUEL SENDER GAUGE ASSEMBLY
23221
2.REMOVE FUEL PUMP
for Type A:
Remove the harness protector from the fuel pump harness.
Disconnect the 2 fuel pump harness connectors.
Disengage the clamp to disconnect the fuel pump harness from the fuel suction plate sub-assembly.
Do not damage the wire harness.
Disengage the clamp to disconnect the tube from the fuel filter.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, separate the fuel filter from the fuel sub-tank.
Do not damage the fuel sub-tank and fuel filter.
Pull out the fuel filter carefully because the O-ring is firmly installed between the fuel filter and fuel sub-tank.
Do not do anything which may separate the tube from either the fuel suction plate sub-assembly or fuel filter, such as applying excessive force to the tube.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Remove the O-ring from the fuel sub-tank.
Disengage the claw to disconnect the fuel pump harness from the fuel pump.
| *a | Fuel Filter |
| *b | Suction Filter |
| *c | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws, and remove the fuel pump from the fuel filter.
Do not damage the fuel filter or suction filter.
Do not remove the suction filter from the fuel pump.
Disconnect the fuel pump harness connector to remove the fuel pump harness from the fuel pump.
| *1 | O-ring |
| *2 | Fuel Pump Spacer |
| *a | 5.0 mm (0.197 in.) |
Remove the O-ring and fuel pump spacer from the fuel pump.
Be careful not to damage the sealing surface.
If the O-ring still remains in the fuel filter, remove it using a wire tip (1 mm (0.0394 in.) diameter) that is formed as shown in the illustration.
for Type B:
Remove the harness protector from the fuel pump harness.
Disconnect the 2 fuel pump harness connectors.
Disengage the clamp to disconnect the fuel pump harness from the fuel suction plate sub-assembly.
Do not damage the wire harness.
| *a | Protective Tape |
| *b | Fuel Pump Filter Hose |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
Do not damage the fuel sub-tank.
Disengage the clamp and disconnect the fuel pump filter hose from the fuel sub-tank.
Do not damage the fuel sub-tank.
| *a | Tube |
Disengage the 2 claws and remove the fuel filter from the fuel sub-tank.
Do not do anything which may separate the tube from either the fuel suction plate sub-assembly or fuel filter, such as applying excessive force to the tube.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Disengage the claw to disconnect the fuel pump harness from the fuel pump.
| *a | Fuel Filter |
| *b | Suction Filter |
| *c | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws, and remove the fuel pump from the fuel filter.
Do not damage the fuel filter or suction filter.
Do not remove the suction filter from the fuel pump.
Disconnect the fuel pump harness connector to remove the fuel pump harness from the fuel pump.
| *1 | O-ring |
| *2 | Fuel Pump Spacer |
| *a | 5.0 mm (0.197 in.) |
Remove the O-ring and fuel pump spacer from the fuel pump.
Be careful not to damage the sealing surface.
If the O-ring still remains in the fuel filter, remove it using a wire tip (1 mm (0.0394 in.) diameter) that is formed as shown in the illustration.