Home › Engine / Hybrid System › M20A-FKS (EMISSION CONTROL) › EGR COOLER › from 2021.02
RM33A0E _51 Engine / Hybrid System _098629 M20A-FKS EMISSION CONTROL _0463333 EGR COOLER A

M20A-FKS EMISSION CONTROL  EGR COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR cooler assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Gas leak from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 82121 5.DISCONNECT ENGINE WIRE

a.
A433438

Remove the 3 bolts.


b.
A433439

Disconnect the 4 connectors.


c.

Disengage the wire harness clamp and disconnect the engine wire.


d.
A443134

Disconnect the 6 connectors.


e.

Disengage the 3 wire harness clamps and disconnect the engine wire.


f.
A443135

Disengage the wire harness clamp.


g.
A443126

Remove the bolt and 2 nuts.


h.

Disconnect the 4 connectors.


i.

Disengage the wire harness clamp and disconnect the engine wire.


Hide 25680 6.REMOVE EGR COOLER ASSEMBLY

a.
A478653C01
2.333,1.083 2.823,1.083 true 0.865,0.708 1.208,0.708 true 2.865,0.99 3.063,1.208 0.198,0.219 10 true *1 0.688,0.615 0.885,0.833 0.198,0.219 10 true *2
*1 No. 3 Water By-pass Hose
*2 No. 4 Water By-pass Hose


Slide the 2 clips and disconnect the No. 3 water by-pass hose and No. 4 water by-pass hose from the EGR cooler assembly.


b.
A478654

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the EGR cooler assembly.


c.
A484598C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Bolt or Nut


Type A:

i.

Remove the 3 bolts, 2 nuts and EGR cooler assembly from the cylinder head sub-assembly and EGR valve assembly.



d.

Type B:

i.

Remove the 2 bolts, 3 nuts and EGR cooler assembly from the cylinder head sub-assembly and EGR valve assembly.



e.
A433446C02
0.51,1.385 0.813,1.385 false 2.552,0.865 2.552,1.135 false 2.479,1.167 2.719,1.375 0.24,0.208 10 false *1 0.354,1.302 0.615,1.51 0.26,0.208 10 false *2
*1 EGR Valve Gasket
*2 EGR Cooler Gasket


Remove the EGR valve gasket from the EGR cooler assembly.


f.

Remove the EGR cooler gasket from the EGR cooler assembly.