Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) › from 2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0341905 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1451  Compressor Solenoid Circuit  


DESCRIPTION

In this circuit, the compressor assembly with pulley (compressor solenoid) receives refrigerant compression demand signals from the air conditioning amplifier assembly.

Based on this signal, the compressor assembly with pulley (compressor solenoid) changes the amount of compressor output.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1451 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Compressor assembly with pulley (compressor solenoid)

·

Harness or connector

·

Air conditioning amplifier assembly


-

WIRING DIAGRAM

E370998E01
1.708,0.677 2.177,0.875 0.469,0.198 10 false SOL+ 1.74,1.469 2.208,1.667 0.469,0.198 10 false SOL- 2.167,0.677 2.396,0.833 0.229,0.156 10 false 2 2.167,1.469 2.396,1.625 0.229,0.156 10 false 1 0.521,2.125 0.854,2.323 0.333,0.198 10 false C98 0.51,2.292 4.542,2.5 4.031,0.208 10 false Compressor Assembly with Pulley (Compressor Solenoid) 4.698,2.115 5.031,2.313 0.333,0.198 10 false K54 4.688,2.281 6.917,2.479 2.229,0.198 10 false Air Conditioning Amplifier Assembly 4.958,0.677 5.188,0.833 0.229,0.156 10 false 3 5.167,0.677 5.635,0.875 0.469,0.198 10 false SOL+ 5.865,0.771 6.063,0.958 0.198,0.188 10 false IC


PROCEDURE

1.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E369146C02
1.469,0.281 1.885,0.542 0.417,0.26 2.323,1.823 1.896,1.313 true 1.542,0.323 2,0.521 0.458,0.198 10 false C98 3.042,3.406 3.385,3.594 0.344,0.188 10 false GND 2.25,1.865 2.813,2.073 0.563,0.208 10 false SOL+ 0.115,0.104 0.49,0.344 0.375,0.24 12 false *a
*a Front view of wire harness connector
(to Compressor Assembly with Pulley (Compressor Solenoid))


Disconnect the C98 compressor assembly with pulley (compressor solenoid) connector.


b.

Using an oscilloscope, check the waveform.

Item Content
Terminal No. C98-2 (SOL+) - Body ground
Tool Setting 5 V/DIV., 500 μs./DIV.
Condition
·

Engine running

·

Blower switch: LO

·

A/C switch: On



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)

NG

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-2 (SOL+) - K54-3 (SOL+) Always Below 1 Ω
C98-2 (SOL+) or K54-3 (SOL+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR