Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2021.02
RM33A0E _51 Engine / Hybrid System _098627 M20A-FKS ENGINE MECHANICAL _0463504 CYLINDER BLOCK A

M20A-FKS ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder block removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of piston or piston ring

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
·

Perform reset memory

·

Perform road test to allow TCM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of front bumper assembly
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

PROCEDURE

Hide 12211 1.REMOVE NO. 1 VENTILATION CASE

CAUTION:

Do not disassembly except if the No. 1 ventilation case to be damaged.


a.
A443404

Remove the 4 bolts and No. 1 ventilation case from the cylinder block sub-assembly.


b.
A425019

Remove the 3 oil separator gaskets from the No. 1 ventilation case.


Hide 11432R 2.REMOVE CYLINDER BLOCK WITH HEAD STRAIGHT SCREW PLUG (w/o Oil Cooler)

a.
A428962

Using a 10 mm hexagon socket wrench, remove the cylinder block with head straight screw plug and gasket from the cylinder block sub-assembly.


Hide 3.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A433302

Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.

Standard Thrust Clearance:

0.160 to 0.512 mm (0.00630 to 0.0202 in.)


Maximum Thrust Clearance:

0.512 mm (0.0202 in.)


HINT:

If the thrust clearance is more than the maximum, replace the connecting rod. If necessary, replace the crankshaft.



Hide 4.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A433303C02
0.708,0.615 0.979,0.26 true 1,0.094 1.302,0.313 0.302,0.219 10 false *a
*a Alignment Mark


Note the alignment marks on the connecting rod and connecting rod cap so that they can be reinstalled to their original locations.


b.
A433304

Using an E12 "TORX" socket wrench, remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.

HINT:

If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.



e.
A433305C02
1.635,0.615 0.813,0.458 true 0.635,0.344 0.948,0.563 0.313,0.219 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


f.
A433306C02
1.594,0.698 0.802,0.615 true 0.625,0.5 0.875,0.781 0.25,0.281 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing the correct direction, and install the connecting rod cap to the connecting rod.


g.
A433307

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


h.

Using an E12 "TORX" socket wrench, install and alternately tighten the 2 connecting rod bolts in several steps.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


i.
A400558C01
2.26,0.802 2.531,0.385 2.531,0.385 2.677,0.385 false 1.396,0.479 1.854,0.677 0.458,0.198 10 false *b 2.729,0.281 3.042,0.479 0.313,0.198 10 false *a
*a Paint Mark
*b 90°
V100135

Front of Engine


Mark the front of each connecting rod bolt with paint.


j.

Tighten the connecting rod bolts 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.



k.

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



l.
A433308C02
1.677,0.969 0.969,0.667 true 1.375,3.167 0.719,3.615 0.719,3.615 1.26,4.208 true 1.385,3.615 0.74,3.615 true 0.802,0.542 1.083,0.708 0.281,0.167 10 false *a 0.542,3.573 0.854,3.729 0.313,0.156 10 false *b
*a Plastigage
*b 1, 2 or 3 Mark


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.032 to 0.065 mm (0.00126 to 0.00256 in.)


Maximum Oil Clearance:

0.065 mm (0.00256 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.

·

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.



Standard Connecting Rod Big End Inside Diameter:
Mark Specified Condition
1 51.000 to 51.008 mm (2.00787 to 2.00818 in.)
2 51.008 to 51.016 mm (2.00818 to 2.00850 in.)
3 51.016 to 51.024 mm (2.00850 to 2.00881 in.)


Standard Connecting Rod Bearing Center Wall Thickness:
Mark Specified Condition
1 1.483 to 1.487 mm (0.05839 to 0.05854 in.)
2 1.487 to 1.491 mm (0.05854 to 0.05870 in.)
3 1.491 to 1.495 mm (0.05870 to 0.05886 in.)


Standard Crank Pin Diameter:

47.992 to 48.000 mm (1.88945 to 1.88976 in.)


NOTICE:

Remove the Plastigage completely after the measurement.



m.

Perform the inspection above for each cylinder.


Hide 5.REMOVE PISTON WITH CONNECTING ROD

a.
A426844C01
1.333,1.094 1.552,1.042 false 1.583,0.938 1.896,1.094 0.313,0.156 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of each cylinder.


b.

Remove the 8 connecting rod bolts, 4 connecting rod caps and 4 connecting rod bearings.


c.

Push the 4 pistons, 4 connecting rods and 4 connecting rod bearings out through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearings, connecting rods and connecting rod caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 6.REMOVE CONNECTING ROD BEARING

a.

Remove the 8 connecting rod bearings from the 4 connecting rods and 4 connecting rod caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 7.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A433309

Using a dial indicator, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.02 to 0.22 mm (0.000787 to 0.00866 in.)


Maximum Thrust Clearance:

0.22 mm (0.00866 in.)


HINT:

If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.


Standard Thrust Washer Thickness:

2.415 to 2.465 mm (0.0951 to 0.0972 in.)



Hide 13411 8.REMOVE CRANKSHAFT

a.
A433310N03
1.375,1.313 1.531,1.51 0.156,0.198 10 false 1 0.677,0.302 0.833,0.5 0.156,0.198 10 true 4 1.75,0.281 1.948,0.448 0.198,0.167 10 true 10 1.229,0.302 1.385,0.458 0.156,0.156 10 true 8 0.667,1.896 0.823,2.094 0.156,0.198 10 true 3 1.219,1.885 1.375,2.083 0.156,0.198 10 true 7 1.802,1.896 1.958,2.094 0.156,0.198 10 true 9 2.354,1.885 2.51,2.083 0.156,0.198 10 true 5 2.917,1.896 3.073,2.063 0.156,0.167 10 true 1 2.917,0.313 3.073,0.49 0.156,0.177 10 true 2 2.354,0.313 2.531,0.469 0.177,0.156 10 true 6

Uniformly loosen and remove the 10 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.


b.

Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.

HINT:
·

Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




c.

Remove the crankshaft from the cylinder block sub-assembly.

HINT:

Keep the No. 1 crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.



d.

Check each crankshaft journal and crankshaft bearing for pitting and scratches.

If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.


Hide 11791 9.REMOVE CRANKSHAFT THRUST WASHER

a.
A400506

Remove the 2 crankshaft thrust washers from the No. 3 journal position of the cylinder block sub-assembly.


Hide 10.REMOVE CRANKSHAFT BEARING

a.

Remove the 5 No. 1 crankshaft bearings and 5 No. 2 crankshaft bearings from the cylinder block sub-assembly and 5 crankshaft bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13011 11.REMOVE PISTON RING SET

a.
A400507C01
1.115,1.76 1.115,1.531 1.115,1.531 1.354,1.281 false 1.063,1.802 1.375,2 0.313,0.198 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring from the piston.


b.

Remove the oil ring expander, upper side rail and lower side rail from the piston by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13101A 12.REMOVE PISTON PIN HOLE SNAP RING

a.
A426847C01
1.885,0.979 2.208,1.188 true 2.104,0.813 2.313,0.375 true 2.25,1.115 2.563,1.271 0.313,0.156 10 false *a 2.344,0.271 2.656,0.427 0.313,0.156 10 false *b
*a Front Mark Cutout Portion
*b Protective Tape


Using a screwdriver, pry out the 2 piston pin hole snap rings from the piston.

HINT:

Tape the screwdriver tip before use.



Hide 13.REMOVE PISTON

a.
A400509

Gradually heat each piston to between 80 and 90°C (176 and 194°F).

CAUTION:

Be sure to wear protective gloves.



b.
A400510

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 15708 14.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A426848

Using a 5 mm hexagon socket wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.


Hide 15709 15.REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A426849

Using a 5 mm hexagon socket wrench, remove the 4 bolts and 4 No. 2 oil nozzle sub-assemblies from the cylinder block sub-assembly.