The electronic throttle and the EPS character change by the operation of the drive mode select switch (electric parking brake switch assembly).
Check each symptom by checking the suspected areas in the table below.
| Result | Proceed to |
|---|---|
| SPORT mode or NORMAL mode is abnormal. | A |
| ECO mode is abnormal. | B |
A
B
Check for DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. | A |
| CAN communication system DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Drive mode select switch (electric parking brake switch assembly)) |
Disconnect the K37 drive mode select switch (electric parking brake switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K37-16 (GND1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K37-9 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect drive mode select switch (electric parking brake switch assembly).
for UA80E: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>INSPECTION
for UB80E: Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>INSPECTION
Drive mode select switch (electric parking brake switch assembly) is normal.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. (for A25A-FKS) | A |
| CAN communication system DTCs are not output. (for 2GR-FKS) | B |
| CAN communication system DTCs are output. | C |
A
B
C
for UA80E: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>INSPECTION
for UB80E: Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>INSPECTION
Reconnect the K37 drive mode select switch (electric parking brake switch assembly) connector.
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the A24 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-12 (PWMS) - Body ground | SPORT mode switch being turned and held | Below 1 Ω |
| A24-12 (PWMS) - Body ground | SPORT mode switch not turned | 10 kΩ or higher |
| A24-13 (SPCN) - Body ground | NORMAL mode switch being pushed and held | Below 1 Ω |
| A24-13 (SPCN) - Body ground | NORMAL mode switch not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K37 drive mode select switch (electric parking brake switch assembly) connector.
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the A23 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-55 (PWMS) - Body ground | SPORT mode switch being turned and held | Below 1 Ω |
| A23-55 (PWMS) - Body ground | SPORT mode switch not turned | 10 kΩ or higher |
| A23-40 (SPCN) - Body ground | NORMAL mode switch being pushed and held | Below 1 Ω |
| A23-40 (SPCN) - Body ground | NORMAL mode switch not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG