Make sure to read "Before Starting Driving Adjustment" before proceeding with work.
Make sure to perform the transition to online axis alignment mode with the vehicle stopped.
Transitioning to online axis alignment mode will erase the learning value, so make sure to complete the adjustment.
Turning the ignition switch off while in online axis alignment mode will cause the system to exit online axis alignment mode, so to continue with the adjustment, it is necessary to transition to online axis alignment mode again.
All of the driving support system functions will be inoperative while the adjustment is in progress.
When driving the vehicle with the GTS connected, be careful with how the wires are routed.
If the adjustment does not complete within a total cumulative time of 15 minutes when the vehicle is driven with all conditions met, perform the adjustment on another route.
If the adjustment does not complete within a total cumulative time of 30 minutes when the vehicle is driven with all conditions met, perform the adjustment using target recognition.
After adjustment is complete, to start the various systems it is necessary to turn the ignition switch off and then to ON again.
In situations such as when the online axis alignment terminates abnormally, to perform online axis alignment again, turn the ignition switch off and then back to ON and enter online axis alignment mode again.
1. PERFORM MILLIMETER WAVE RADAR SENSOR OPTICAL AXIS LEARNING (When driving with GTS connected to vehicle)
Adjust the tire pressures to the standard values.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Make sure the surfaces of the radiator grille emblem and millimeter wave radar sensor assembly are clean and have no dirt, snow, or other matter adhering to them.
Clean away any foreign matter adhering to the surface of the radiator grille emblem.
Check that there is no damage or deformation around the front exterior area of the vehicle.
Check that the radiator grille sub-assembly and front bumper assembly are securely installed, and that there is no damage or deformation around the installation areas. If any abnormalities are found, repair or replace parts as necessary.
| *A | for Bar Type Radiator Grille | *B | for Mesh Type Radiator Grille |
| *a | Radiator Grille Sub-assembly Installation Areas to Inspect | *b | Front Bumper Assembly Installation Areas to Inspect |
| *a | Millimeter Wave Radar Sensor Assembly Installation Areas to Inspect |
Check that the millimeter wave radar sensor assembly is securely installed and if any abnormalities are found, securely install the millimeter wave radar sensor assembly and then perform optical axis learning.
Check the levelness of the ground.
|
Levelness Check Point |
Check the levelness of the ground at the 2 points shown in the illustration.
Place the level on each levelness check point and check that the air bubble of the level is centered.
Front Radar Acceleration Sensor Calibration
With the ignition switch off, connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Radar Acceleration Sensor Calibration.
| Tester Display |
|---|
| Front Radar Acceleration Sensor Calibration |
Perform the calibration according to the display on the GTS.
If an error code is displayed, perform troubleshooting according to the following table, then perform the calibration again.
Transition to online axis alignment mode
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Transition to Online Axis Alignment Mode.
| Tester Display |
|---|
| Transition to Online Axis Alignment Mode |
Confirm the conditions displayed on the screen and then press "Next".
Select "Front radar sensor" and then press "Next".
Check the GTS screen and confirm that it has transitioned to online axis alignment mode.
Press "Next".
Online axis adjustment (Optical Axis Learning)
Drive the vehicle to perform optical axis learning.
If the alignment is performed with the GTS connected to the vehicle, the alignment progress can be monitored through 5 stages on the GTS screen.
If the online axis alignment completes normally, the buzzer will sound intermittently for 2 seconds.
If the alignment terminates abnormally, the buzzer will sound for 3 seconds continuously.
If an error code is displayed, perform troubleshooting according to the following table, then perform the beam axis alignment again.
Press "Exit" to exit the Online axis adjustment mode.
Turn the ignition switch off.
Turn the ignition switch to ON and check that the warning light turns off.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
After beam axis adjustment completes, clear the following system vehicle control history entries.
Clear vehicle control history (Dynamic Radar Cruise Control System).
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lane Tracing Assist System).
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Road Sign Assist System).
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Front Radar Sensor System).
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Pre-collision System).
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lighting System).
2. PERFORM MILLIMETER WAVE RADAR SENSOR OPTICAL AXIS LEARNING (When driving with GTS not connected to vehicle)
Adjust the tire pressures to the standard values.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Make sure the surfaces of the radiator grille emblem and millimeter wave radar sensor assembly are clean and have no dirt, snow, or other matter adhering to them.
Clean away any foreign matter adhering to the surface of the radiator grille emblem.
Check that there is no damage or deformation around the front exterior area of the vehicle.
Check that the radiator grille sub-assembly and front bumper assembly are securely installed, and that there is no damage or deformation around the installation areas. If any abnormalities are found, repair or replace parts as necessary.
| *A | for Bar Type Radiator Grille | *B | for Mesh Type Radiator Grille |
| *a | Radiator Grille Sub-assembly Installation Areas to Inspect | *b | Front Bumper Assembly Installation Areas to Inspect |
| *a | Millimeter Wave Radar Sensor Assembly Installation Areas to Inspect |
Check that the millimeter wave radar sensor assembly is securely installed and if any abnormalities are found, securely install the millimeter wave radar sensor assembly and then perform optical axis learning.
Check the levelness of the ground.
|
Levelness Check Point |
Check the levelness of the ground at the 2 points shown in the illustration.
Place the level on each levelness check point and check that the air bubble of the level is centered.
Front Radar Acceleration Sensor Calibration
With the ignition switch off, connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Radar Acceleration Sensor Calibration.
| Tester Display |
|---|
| Front Radar Acceleration Sensor Calibration |
Perform the calibration according to the display on the GTS.
If an error code is displayed, perform troubleshooting according to the following table, then perform the calibration again.
Transition to online axis alignment mode
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Transition to Online Axis Alignment Mode.
| Tester Display |
|---|
| Transition to Online Axis Alignment Mode |
Confirm the conditions displayed on the screen and then press "Next".
Select "Front radar sensor" and then press "Next".
Check the GTS screen and confirm that it has transitioned to online axis alignment mode.
Press "Next".
In accordance with the instructions on the screen press "Exit" and then disconnect the GTS from the DLC3.
Online axis adjustment (Optical Axis Learning)
Drive the vehicle to perform optical axis learning.
If the online axis alignment completes normally, the buzzer will sound intermittently for 2 seconds.
If the alignment terminates abnormally, the buzzer will sound for 3 seconds continuously.
Turn the ignition switch off.
Turn the ignition switch to ON and check that the warning light turns off.
Turn the ignition switch off.
After beam axis adjustment completes, clear the following system vehicle control history entries.
Clear vehicle control history (Dynamic Radar Cruise Control System).
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lane Tracing Assist System).
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Road Sign Assist System).
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Front Radar Sensor System).
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Pre-collision System).
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lighting System).