The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication. If a communication malfunction between the forward recognition camera and millimeter wave radar sensor assembly is detected, DTC U023587 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Missing Message | Once 3 seconds elapse after turning the ignition switch to ON, a communication malfunction between the millimeter wave radar sensor assembly continues for approximately 2 seconds or more. | ·
Harness or connector ·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
| Pattern | DTC output part name
(Display on GTS) |
Suspected Area (Malfunction Status) | ||||
|---|---|---|---|---|---|---|
| Forward Recognition Camera | Millimeter Wave Radar Sensor Assembly | |||||
| Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Front Radar Sensor | ||
| U023587 | U023587 | U023587 | U023587 | U010487 | ||
|
○: DTC is output -: DTC is not output |
||||||
| Pattern 1 | ○ | ○ | ○ | ○ | ○ | Harness or connector (Open or short) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||
| Forward recognition camera (Internal malfunction) | ||||||
| Pattern 2 | ○ | ○ | ○ | ○ | - | Forward recognition camera (Internal malfunction) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||
If the DTCs are output simultaneously, the inspection area can be narrowed down.
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When disconnecting and reconnecting the battery
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Read each DTC and check the diagnosis pattern using the table below.
| Pattern | DTC output part name
(Display on GTS) |
||||
|---|---|---|---|---|---|
| Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Front Radar Sensor | |
| Pattern 1 | U023587 | U023587 | U023587 | U023587 | U010487 |
| Pattern 2 | U023587 | U023587 | U023587 | U023587 | - |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
A
B
| *A | Before Jan. 2022 Production |
| *B | From Jan. 2022 Production |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-6 (CANH) - V6-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| V6-6 (CANH) - Body ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| V6-12 (CANL) - Body ground | ||
| V6-6 (CANH) - +B | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| V6-12 (CANL) - +B |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V25-6 (CANH) - V25-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| V25-6 (CANH) - Body ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| V25-12 (CANL) - Body ground | ||
| V25-6 (CANH) - +B | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| V25-12 (CANL) - +B |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-5 (CA1P) - A30-6 (CA1N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A30-5 (CA1P) - Body ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A30-6 (CA1N) - Body ground | ||
| A30-5 (CA1P) - +B | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A30-6 (CA1N) - +B |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | Before Jan. 2022 Production |
| *B | From Jan. 2022 Production |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the forward recognition camera connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| V6-6 (CANH) - V6-12 (CANL) | Ignition switch ON | 1V/DIV., 100μs./DIV. | Pulse generation |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| V25-6 (CANH) - V25-12 (CANL) | Ignition switch ON | 1V/DIV., 100μs./DIV. | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG