The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
1.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
55972C
2.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT (for LHD)
55086
3.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)
86101
4.REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)
w/ Antenna Divider:
Disconnect the connector.
w/o Navigation Antenna:
Disengage the 5 clamps and remove the antenna cord sub-assembly.
w/ Navigation Antenna:
Disconnect the connector.
| *A | w/ Branch Line | - | - |
Disengage the 2 claws.
Disengage each clamp and remove the antenna cord sub-assembly.
55971C
5.REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT (for RHD)
Use the same procedure as for LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>DISASSEMBLY
55086
6.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)
Use the same procedure as for LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>DISASSEMBLY
55972C
7.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT (for RHD)
w/ Headup Display:
Use the same procedure as for LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>DISASSEMBLY
55950G
8.REMOVE DEFROSTER NOZZLE ASSEMBLY (for RHD)
w/ Headup Display:
Use the same procedure as for LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>DISASSEMBLY
83108
9.REMOVE METER MIRROR SUB-ASSEMBLY (for RHD)
w/ Headup Display:
Use the same procedure as for LHD.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY>REMOVAL
55084E
10.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)
Use the same procedure as for LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>DISASSEMBLY
86101
11.REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)
Disconnect the connector.
| *A | w/ Branch Line | - | - |
Disengage the 2 claws.
Disengage each clamp and remove the antenna cord sub-assembly.
12.REMOVE ROOF HEADLINING ASSEMBLY
86101J
13.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY
w/o Television Antenna:
Remove the adhesive tape from the roof headlining assembly.
for Normal Roof:
|
Adhesive Tape | - | - |
for Moon Roof:
|
Adhesive Tape | - | - |
for Panoramic Moon Roof:
|
Adhesive Tape | - | - |
Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.
w/ Television Antenna:
Remove the adhesive tape from the roof headlining assembly.
| *A | for Normal Roof | *B | for Panoramic Moon Roof |
|
Adhesive Tape | - | - |
Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.
86101Q
14.REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)
w/o Telematics Transceiver:
Disconnect the connector.
Disengage the 9 clamps to remove the No. 4 antenna cord sub-assembly.
86101R
15.REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)
w/ Telematics Transceiver:
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL