Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328874 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System)  C1AED  Rear Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AED Rear Sensor Communication Malfunction An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the engine switch is turned on (IG).
·

Rear ultrasonic sensor circuit

·

Harness or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

for 4-sensor Type
E231492E89
2.938,1.948 4.365,2.5 1.427,0.552 10 false Rear Corner Ultrasonic Sensor RH 5.677,1.927 6.875,2.365 1.198,0.438 10 false Clearance Warning ECU Assembly 0.292,1.781 0.594,1.948 0.302,0.167 10 false X6 2.938,1.771 3.292,2.094 0.354,0.323 10 false X5 5.667,1.781 6.052,2.042 0.385,0.26 10 false R39 1.198,0.948 1.604,1.302 0.406,0.354 10 false BI 1.198,1.365 1.563,1.719 0.365,0.354 10 false EI 1.198,0.49 1.438,0.677 0.24,0.188 10 false SI 3.854,0.948 4.344,1.271 0.49,0.323 10 false BI 3.844,1.406 4.229,1.688 0.385,0.281 10 false EI 3.844,0.5 4.188,0.781 0.344,0.281 10 false SI 3.177,0.917 3.604,1.219 0.427,0.302 10 false BO 3.177,1.417 3.615,1.729 0.438,0.313 10 false EO 3.167,0.479 3.552,0.781 0.385,0.302 10 false SO 5.854,0.5 6.208,0.688 0.354,0.188 10 false SOR 5.854,1.417 6.292,1.667 0.438,0.25 10 false E1 5.854,0.948 6.448,1.24 0.594,0.292 10 false BOR 1.469,0.375 1.76,0.656 0.292,0.281 10 false 3 1.469,0.833 1.708,1.135 0.24,0.302 10 false 1 1.469,1.302 1.75,1.563 0.281,0.26 10 false 5 4.156,0.375 4.396,0.688 0.24,0.313 10 false 3 4.156,0.844 4.385,1.167 0.229,0.323 10 false 1 4.156,1.292 4.5,1.615 0.344,0.323 10 false 5 2.958,0.385 3.188,0.625 0.229,0.24 10 false 4 2.958,0.844 3.219,1.135 0.26,0.292 10 false 2 2.958,1.292 3.271,1.552 0.313,0.26 10 false 6 5.573,0.385 5.906,0.719 0.333,0.333 10 false 24 5.573,0.844 5.875,1.177 0.302,0.333 10 false 22 5.573,1.281 5.875,1.583 0.302,0.302 10 false 23 0.292,1.979 1.708,2.479 1.417,0.5 10 false Rear Corner Ultrasonic Sensor LH

for 6-sensor Type
E462783E02
2.875,3.948 4.344,4.354 1.469,0.406 10 false Rear Center Ultrasonic Sensor LH 5.427,3.948 6.854,4.333 1.427,0.385 10 false Rear Corner Ultrasonic Sensor LH 0.375,3.958 1.865,4.375 1.49,0.417 10 false Rear Center Ultrasonic Sensor RH 3.865,0.969 4.031,1.25 0.167,0.281 10 false BI 3.865,1.354 4.063,1.604 0.198,0.25 10 false EI 3.854,0.573 4.042,0.854 0.188,0.281 10 false SI 3.146,0.948 3.427,1.208 0.281,0.26 10 false BO 3.146,1.354 3.417,1.594 0.271,0.24 10 false EO 3.146,0.563 3.417,0.833 0.271,0.271 10 false SO 1.323,0.969 1.531,1.208 0.208,0.24 10 false BI 1.323,1.354 1.521,1.594 0.198,0.24 10 false EI 1.323,0.573 1.521,0.813 0.198,0.24 10 false SI 1.25,3.094 1.49,3.333 0.24,0.24 10 false BO 1.26,3.479 1.542,3.771 0.281,0.292 10 false EO 1.24,2.698 1.458,2.969 0.219,0.271 10 false SO 5.688,3.5 5.917,3.76 0.229,0.26 10 false EI 5.677,2.688 5.896,2.906 0.219,0.219 10 false SI 5.688,3.094 5.885,3.323 0.198,0.229 10 false BI 4.094,0.427 4.25,0.583 0.156,0.156 10 false 3 2.969,0.823 3.073,0.979 0.104,0.156 10 false 2 2.969,0.427 3.104,0.594 0.135,0.167 10 false 4 4.094,1.24 4.25,1.396 0.156,0.156 10 false 5 4.094,0.823 4.25,0.979 0.156,0.156 10 false 1 2.969,1.24 3.188,1.417 0.219,0.177 10 false 6 1.542,0.427 1.698,0.583 0.156,0.156 10 false 3 1.552,2.958 1.708,3.115 0.156,0.156 10 false 2 1.552,2.573 1.708,2.729 0.156,0.156 10 false 4 1.552,1.24 1.708,1.396 0.156,0.156 10 false 5 1.552,0.823 1.708,0.979 0.156,0.156 10 false 1 1.552,3.375 1.708,3.531 0.156,0.156 10 false 6 5.5,2.573 5.604,2.729 0.104,0.156 10 false 3 5.51,3.385 5.615,3.542 0.104,0.156 10 false 5 5.5,2.969 5.604,3.125 0.104,0.156 10 false 1 3.156,3.094 3.354,3.354 0.198,0.26 10 false BI 3.156,3.49 3.333,3.74 0.177,0.25 10 false EI 3.146,2.688 3.333,3 0.188,0.313 10 false SI 3.792,3.094 4.083,3.333 0.292,0.24 10 false BO 3.792,3.49 4.052,3.771 0.26,0.281 10 false EO 3.792,2.688 4.094,2.906 0.302,0.219 10 false SO 4.104,2.573 4.26,2.729 0.156,0.156 10 false 4 2.969,2.969 3.073,3.125 0.104,0.156 10 false 1 2.969,2.573 3.073,2.729 0.104,0.156 10 false 3 4.104,3.375 4.26,3.531 0.156,0.156 10 false 6 4.104,2.958 4.26,3.115 0.156,0.156 10 false 2 2.958,3.385 3.063,3.542 0.104,0.156 10 false 5 2.875,3.792 3.135,3.958 0.26,0.167 10 false X8 0.375,3.802 0.667,3.969 0.292,0.167 10 false X7 5.51,1.823 6.74,2.156 1.229,0.333 10 false Clearance Warning ECU Assembly 5.688,0.958 6.104,1.208 0.417,0.25 10 false BOR 5.688,1.354 6.104,1.635 0.417,0.281 10 false E1 5.677,0.563 6.135,0.854 0.458,0.292 10 false SOR 5.438,0.854 5.75,1.063 0.313,0.208 10 false 22 5.438,1.25 5.615,1.406 0.177,0.156 10 false 23 5.438,0.469 5.823,0.625 0.385,0.156 10 false 24 5.51,1.677 5.802,1.844 0.292,0.167 10 false R39 5.438,3.802 5.708,3.969 0.271,0.167 10 false X6 2.875,1.802 4.333,2.198 1.458,0.396 10 false Rear Corner Ultrasonic Sensor RH 2.875,1.646 3.135,1.813 0.26,0.167 10 false X5

PROCEDURE

1.CLEARANCE SONAR SYSTEM REGISTRATION

NEXT

2.CHECK DTC OUTPUT (C1AED)
2.CHECK DTC OUTPUT (C1AED)
a.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

b.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

c.

Recheck for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output (for 4-sensor Type) A
DTC C1AED is output (for 6-sensor Type) B
No DTCs are output C



A

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR RH)

B

11.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR RH)

C

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR RH)
a.

Disconnect the R39 clearance warning ECU assembly connector.


b.

Disconnect the X5 rear corner ultrasonic sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-22 (BOR) - X5-1 (BI) Always Below 1 Ω
R39-24 (SOR) - X5-3 (SI) Always Below 1 Ω
R39-23 (E1) - X5-5 (EI) Always Below 1 Ω
R39-22 (BOR) or X5-1 (BI) - Body ground Always 10 kΩ or higher
R39-24 (SOR) or X5-3 (SI) - Body ground Always 10 kΩ or higher
R39-23 (E1) or X5-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR RH - REAR CORNER ULTRASONIC SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR RH - REAR CORNER ULTRASONIC SENSOR LH)
a.

Disconnect the X6 rear corner ultrasonic sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X5-2 (BO) - X6-1 (BI) Always Below 1 Ω
X5-4 (SO) - X6-3 (SI) Always Below 1 Ω
X5-6 (EO) - X6-5 (EI) Always Below 1 Ω
X5-2 (BO) or X6-1 (BI) - Body ground Always 10 kΩ or higher
X5-4 (SO) or X6-3 (SI) - Body ground Always 10 kΩ or higher
X5-6 (EO) or X6-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT REAR CORNER ULTRASONIC SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR CORNER ULTRASONIC SENSOR RH
a.
E379464C01
1.448,1.5 0.875,1.146 false 2.531,2.49 1.958,2.135 false 2.51,1.833 1.958,1.833 false 2.469,1.167 1.958,1.531 false 1.417,2.156 0.906,2.521 false 1.448,1.833 0.896,1.833 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 2.531,1.073 2.844,1.271 0.313,0.198 10 false BI 2.573,1.75 2.885,1.948 0.313,0.198 10 false SI 2.583,2.427 2.896,2.625 0.313,0.198 10 false EI 0.656,1.021 0.969,1.219 0.313,0.198 10 false BO 0.667,1.76 0.979,1.958 0.313,0.198 10 false SO 0.677,2.49 0.99,2.688 0.313,0.198 10 false EO
*a Component without harness connected
(Rear Corner Ultrasonic Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT REAR CORNER ULTRASONIC SENSOR LH

NG

6.INSPECT REAR CORNER ULTRASONIC SENSOR LH
a.
E379464C05
2.531,2.49 1.958,2.135 false 2.51,1.833 1.958,1.833 false 2.469,1.167 1.958,1.531 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 2.531,1.073 2.844,1.271 0.313,0.198 10 false BI 2.573,1.75 2.885,1.948 0.313,0.198 10 false SI 2.583,2.427 2.896,2.625 0.313,0.198 10 false EI
*a Component without harness connected
(Rear Corner Ultrasonic Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 Always 10 kΩ or higher
3 (SI) - 4 Always Below 1 Ω
5 (EI) - 6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.REPLACE REAR CORNER ULTRASONIC SENSOR LH

NG

7.REPLACE REAR CORNER ULTRASONIC SENSOR LH

NEXT

8.CHECK DTC OUTPUT (C1AED)
8.CHECK DTC OUTPUT (C1AED)
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output A
No DTCs are output B



A

9.REPLACE REAR CORNER ULTRASONIC SENSOR RH

B

END (REAR CORNER ULTRASONIC SENSOR LH WAS DEFECTIVE)

9.REPLACE REAR CORNER ULTRASONIC SENSOR RH

NEXT

10.CHECK DTC OUTPUT (C1AED)
10.CHECK DTC OUTPUT (C1AED)
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output A
No DTCs are output B



A

B

END (REAR CORNER ULTRASONIC SENSOR RH WAS DEFECTIVE)

11.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR RH)
a.

Disconnect the R39 clearance warning ECU assembly connector.


b.

Disconnect the X5 rear corner ultrasonic sensor RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-22 (BOR) - X5-1 (BI) Always Below 1 Ω
R39-24 (SOR) - X5-3 (SI) Always Below 1 Ω
R39-23 (E1) - X5-5 (EI) Always Below 1 Ω
R39-22 (BOR) or X5-1 (BI) - Body ground Always 10 kΩ or higher
R39-24 (SOR) or X5-3 (SI) - Body ground Always 10 kΩ or higher
R39-23 (E1) or X5-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR RH - REAR CENTER ULTRASONIC SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR RH - REAR CENTER ULTRASONIC SENSOR RH)
a.

Disconnect the X7 rear center ultrasonic sensor RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X5-2 (BO) - X7-1 (BI) Always Below 1 Ω
X5-4 (SO) - X7-3 (SI) Always Below 1 Ω
X5-6 (EO) - X7-5 (EI) Always Below 1 Ω
X5-2 (BO) or X7-1 (BI) - Body ground Always 10 kΩ or higher
X5-4 (SO) or X7-3 (SI) - Body ground Always 10 kΩ or higher
X5-6 (EO) or X7-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR RH - REAR CENTER ULTRASONIC SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR RH - REAR CENTER ULTRASONIC SENSOR LH)
a.

Disconnect the X8 rear center ultrasonic sensor LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X7-2 (BO) - X8-1 (BI) Always Below 1 Ω
X7-4 (SO) - X8-3 (SI) Always Below 1 Ω
X7-6 (EO) - X8-5 (EI) Always Below 1 Ω
X7-2 (BO) or X8-1 (BI) - Body ground Always 10 kΩ or higher
X7-4 (SO) or X8-3 (SI) - Body ground Always 10 kΩ or higher
X7-6 (EO) or X8-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR LH - REAR CORNER ULTRASONIC SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR LH - REAR CORNER ULTRASONIC SENSOR LH)
a.

Disconnect the X6 rear corner ultrasonic sensor LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X8-2 (BO) - X6-1 (BI) Always Below 1 Ω
X8-4 (SO) - X6-3 (SI) Always Below 1 Ω
X8-6 (EO) - X6-5 (EI) Always Below 1 Ω
X8-2 (BO) or X6-1 (BI) - Body ground Always 10 kΩ or higher
X8-4 (SO) or X6-3 (SI) - Body ground Always 10 kΩ or higher
X8-6 (EO) or X6-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT REAR CORNER ULTRASONIC SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT REAR CORNER ULTRASONIC SENSOR RH
a.
E379464C10
1.448,1.5 0.875,1.146 false 2.531,2.49 1.958,2.135 false 2.51,1.833 1.958,1.833 false 2.469,1.167 1.958,1.531 false 1.417,2.156 0.906,2.521 false 1.448,1.833 0.896,1.833 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 2.531,1.073 2.844,1.271 0.313,0.198 10 false BI 2.573,1.75 2.885,1.948 0.313,0.198 10 false SI 2.583,2.427 2.896,2.625 0.313,0.198 10 false EI 0.656,1.021 0.969,1.219 0.313,0.198 10 false BO 0.667,1.76 0.979,1.958 0.313,0.198 10 false SO 0.677,2.49 0.99,2.688 0.313,0.198 10 false EO
*a Component without harness connected
(Rear Corner Ultrasonic Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT REAR CENTER ULTRASONIC SENSOR RH

NG

16.INSPECT REAR CENTER ULTRASONIC SENSOR RH
a.
E379464C11
1.448,1.5 0.875,1.146 false 2.531,2.49 1.958,2.135 false 2.51,1.833 1.958,1.833 false 2.469,1.167 1.958,1.531 false 1.417,2.156 0.906,2.521 false 1.448,1.833 0.896,1.833 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 2.531,1.073 2.844,1.271 0.313,0.198 10 false BI 2.573,1.75 2.885,1.948 0.313,0.198 10 false SI 2.583,2.427 2.896,2.625 0.313,0.198 10 false EI 0.656,1.021 0.969,1.219 0.313,0.198 10 false BO 0.667,1.76 0.979,1.958 0.313,0.198 10 false SO 0.677,2.49 0.99,2.688 0.313,0.198 10 false EO
*a Component without harness connected
(Rear Center Ultrasonic Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.INSPECT REAR CENTER ULTRASONIC SENSOR LH

NG

17.INSPECT REAR CENTER ULTRASONIC SENSOR LH
a.
E379464C12
1.448,1.5 0.875,1.146 false 2.531,2.49 1.958,2.135 false 2.51,1.833 1.958,1.833 false 2.469,1.167 1.958,1.531 false 1.417,2.156 0.906,2.521 false 1.448,1.833 0.896,1.833 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 2.531,1.073 2.844,1.271 0.313,0.198 10 false BI 2.573,1.75 2.885,1.948 0.313,0.198 10 false SI 2.583,2.427 2.896,2.625 0.313,0.198 10 false EI 0.656,1.021 0.969,1.219 0.313,0.198 10 false BO 0.667,1.76 0.979,1.958 0.313,0.198 10 false SO 0.677,2.49 0.99,2.688 0.313,0.198 10 false EO
*a Component without harness connected
(Rear Center Ultrasonic Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.INSPECT REAR CORNER ULTRASONIC SENSOR LH

NG

18.INSPECT REAR CORNER ULTRASONIC SENSOR LH
a.
E379464C13
2.531,2.49 1.958,2.135 false 2.51,1.833 1.958,1.833 false 2.469,1.167 1.958,1.531 false 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 2.531,1.073 2.844,1.271 0.313,0.198 10 false BI 2.573,1.75 2.885,1.948 0.313,0.198 10 false SI 2.583,2.427 2.896,2.625 0.313,0.198 10 false EI
*a Component without harness connected
(Rear Corner Ultrasonic Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 Always 10 kΩ or higher
3 (SI) - 4 Always Below 1 Ω
5 (EI) - 6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.REPLACE REAR CORNER ULTRASONIC SENSOR RH

NG

19.REPLACE REAR CORNER ULTRASONIC SENSOR RH

NEXT

20.CHECK DTC OUTPUT (C1AED)
20.CHECK DTC OUTPUT (C1AED)
a.

Clear the DTCs.

Body Electrical > Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output A
No DTCs are output B



A

21.REPLACE REAR CENTER ULTRASONIC SENSOR RH

B

END (REAR CORNER ULTRASONIC SENSOR RH WAS DEFECTIVE)

21.REPLACE REAR CENTER ULTRASONIC SENSOR RH

NEXT

22.CHECK DTC OUTPUT (C1AED)
22.CHECK DTC OUTPUT (C1AED)
a.

Clear the DTCs.

Body Electrical > Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output A
No DTCs are output B



A

23.REPLACE REAR CENTER ULTRASONIC SENSOR LH

B

END (REAR CENTER ULTRASONIC SENSOR RH WAS DEFECTIVE)

23.REPLACE REAR CENTER ULTRASONIC SENSOR LH

NEXT

24.CHECK DTC OUTPUT (C1AED)
24.CHECK DTC OUTPUT (C1AED)
a.

Clear the DTCs.

Body Electrical > Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output A
No DTCs are output B



A

25.REPLACE REAR CORNER ULTRASONIC SENSOR LH

B

END (REAR CENTER ULTRASONIC SENSOR LH WAS DEFECTIVE)

25.REPLACE REAR CORNER ULTRASONIC SENSOR LH

NEXT

26.CHECK DTC OUTPUT (C1AED)
26.CHECK DTC OUTPUT (C1AED)
a.

Clear the DTCs.

Body Electrical > Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AED is output A
No DTCs are output B



A

B

END (REAR CORNER ULTRASONIC SENSOR LH WAS DEFECTIVE)