Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C05061F  Right Front Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

Refer to DTC C050612

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C050612

DTC No. Detection Item DTC Detection Condition Trouble Area
C05061F Right Front Wheel Speed Sensor Circuit Intermittent
·

The speed sensor signal is excessively noisy.

·

The calculated change in wheel speed is more than 980 m/s2 for 5*1 or 20*2 seconds or more.

·

The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2 for 5*1 or 20*2 seconds or more.

·

When the vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds for 5*1 or 20*2 seconds or more.


·

Front speed sensor RH

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)



*1: The stop light switch assembly is OFF.

*2: The stop light switch assembly is ON.


DTC Detection Conditions: C05061F
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The Stop light switch assembly is OFF. - ○ ○ ○
Malfunction Status The speed sensor signal is excessively noisy. ○ - - -
The calculated change in wheel speed is more than 980 m/s2. - ○ - -
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2. - - ○ -
The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds. - - - ○
Detection Time - 5 seconds or more. 5 seconds or more. 5 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C05061F
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition The stop light switch assembly is ON. ○ ○ ○
Malfunction Status The calculated change in wheel speed is more than 980 m/s2. ○ - -
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2. - ○ -
The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds. - - ○
Detection Time 20 seconds or more. 20 seconds or more. 20 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PRECAUTION

Procedure to clear warning lights (When not clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle at 54 km/h (34 mph) or more for 3 seconds or more to clear the warning lights.





PROCEDURE

1.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the front speed sensor RH.

OK:

The front speed sensor RH tip is free of oil and foreign matter.


HINT:

If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor RH, this DTC may be stored.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

7.CLEAN FRONT SPEED SENSOR RH
2.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the front speed sensor rotor RH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor rotor RH.

OK:

The front speed sensor rotor RH is free of oil and foreign matter.


HINT:

If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor rotor RH, this DTC may be stored.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH

for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


NG

3.CLEAN FRONT SPEED SENSOR ROTOR RH
3.CLEAN FRONT SPEED SENSOR ROTOR RH
a.

Clean the front speed sensor rotor RH.

NOTICE:

Do not use parts cleaner when cleaning the front speed sensor rotor RH.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Operate the GTS to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Clear DTCs
50002 435

d.

Press the DTC clear button.


Result:
Proceed to
NEXT



NEXT

5.PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
5.PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > Brake/EPB > Utility
Tester Display
Signal Check
50005 435 4558
OK:

Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.



Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH

for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


6.RECONFIRM DTC
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


d.

Read the DTCs following the prompts on the GTS. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes
50001 435

e.

Check if the same DTC is output.


Result:
Result Proceed to
C05061F is not output A
C05061F is output B



A

END

B

REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH

for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


7.CLEAN FRONT SPEED SENSOR RH
a.

Clean the front speed sensor RH.

NOTICE:

When cleaning the front speed sensor RH, make sure to clean the installation hole before installation.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Operate the GTS to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Clear DTCs
50002 435

d.

Press the DTC clear button.


Result:
Proceed to
NEXT



NEXT

9.PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
9.PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > Brake/EPB > Utility
Tester Display
Signal Check
50005 435 4558
OK:

Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

2.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
10.RECONFIRM DTC
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


d.

Read the DTCs following the prompts on the GTS. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes
50001 435

e.

Check if the same DTC is output.


Result:
Result Proceed to
C05061F is not output A
C05061F is output B



A

END

B

2.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)