Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C050C12  Left Rear Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS control.

The speed sensor detects the magnetic fields of the speed sensor rotor as it rotates and outputs a pulse signal.

The frequency of the pulse varies in accordance with the rotational speed of the speed sensor rotor and the system uses this to determine the wheel speed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C050C12 Left Rear Wheel Speed Sensor Circuit Short to Battery A short to +B in the speed sensor signal circuit is detected for 0.12 seconds or more.
·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Wire harness or connector

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C480603E86
0.604,2.323 2.031,2.896 1.427,0.573 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 2.271,2.302 4.094,2.854 1.823,0.552 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly) 5.25,3.104 6.771,3.698 1.521,0.594 10 false Skid Control ECU (Brake Actuator Assembly) 5.292,1.26 5.75,1.458 0.458,0.198 10 false RL+ 3.24,1.146 3.698,1.344 0.458,0.198 10 false RL+ 1.635,1.125 2.094,1.323 0.458,0.198 10 false LA+ 2.448,1.135 2.906,1.333 0.458,0.198 10 false LA+ 1.635,1.833 2.094,2.031 0.458,0.198 10 false LA- 2.448,1.823 2.906,2.021 0.458,0.198 10 false LA- 3.24,1.823 3.698,2.021 0.458,0.198 10 false RL- 5.292,1.948 5.75,2.146 0.458,0.198 10 false RL- 2.063,1.135 2.521,1.333 0.458,0.198 10 false v2 2.073,1.823 2.531,2.021 0.458,0.198 10 false v2 3.625,1.813 4.031,2.031 0.406,0.219 10 false vR1 2.104,1.604 2.406,1.833 0.302,0.229 10 false 1 5.271,2.969 5.729,3.167 0.458,0.198 10 false A34 2.104,0.927 2.406,1.156 0.302,0.229 10 false 2 3.708,0.927 4.01,1.156 0.302,0.229 10 false 1 3.719,1.625 4.021,1.854 0.302,0.229 10 false 2 4.99,1.01 5.292,1.24 0.302,0.229 10 false 39 4.979,1.688 5.281,1.917 0.302,0.229 10 false 23 3.625,1.125 4.031,1.344 0.406,0.219 10 false vR1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C447247C19
0.354,0.677 0.74,0.948 0.385,0.271 2.083,1.75 1.844,1.146 true 1.417,1.75 1.594,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,0.729 0.771,0.927 0.313,0.198 10 false v2 2.021,1.802 2.417,2.021 0.396,0.219 10 false LA+ 1.313,1.792 1.708,2.01 0.396,0.219 10 false LA-
*a Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)
(to Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the v2 rear speed sensor LH (rear axle hub and bearing assembly LH) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
v2-2 (LA+) - v2-1 (LA-) Ignition switch on 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C401699C98
0.49,0.75 0.906,1.042 0.417,0.292 1.438,1.729 1.604,1.229 true 2.073,1.729 1.823,1.229 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.583,0.802 1.042,1 0.458,0.198 10 false vR1 1.344,1.771 1.802,1.969 0.458,0.198 10 false RL- 2.021,1.771 2.479,1.969 0.458,0.198 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
vR1-1 (RL+) - vR1-2 (RL-) Ignition switch on 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.
C401699C99
0.281,0.844 0.688,1.115 0.406,0.271 1.156,1.719 1.573,1.219 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 0.365,0.906 0.823,1.104 0.458,0.198 10 false vR1 1.052,1.75 1.51,1.948 0.458,0.198 10 false RL-
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
vR1-2 (RL-) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
vR1-1 (RL+) or A34-39 (RL+) - vR1-2 (RL-) or A34-23 (RL-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR