Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C05121F  Right Rear Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

Refer to DTC C051212

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C051212

DTC No. Detection Item DTC Detection Condition Trouble Area
C05121F Right Rear Wheel Speed Sensor Circuit Intermittent
·

The speed sensor signal is excessively noisy.

·

The calculated change in wheel speed is more than 980 m/s2 for 5*1 or 20*2 seconds or more.

·

The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2 for 5*1 or 20*2 seconds or more.

·

When the vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds for 5*1 or 20*2 seconds or more.


·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)



*1: The stop light switch assembly is OFF.

*2: The stop light switch assembly is ON.


DTC Detection Conditions: C05121F
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The Stop light switch assembly is OFF. - ○ ○ ○
Malfunction Status The speed sensor signal is excessively noisy. ○ - - -
The calculated change in wheel speed is more than 980 m/s2. - ○ - -
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2. - - ○ -
The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds. - - - ○
Detection Time - 5 seconds or more. 5 seconds or more. 5 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C05121F
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition The stop light switch assembly is ON. ○ ○ ○
Malfunction Status The calculated change in wheel speed is more than 980 m/s2. ○ - -
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2. - ○ -
The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds. - - ○
Detection Time 20 seconds or more. 20 seconds or more. 20 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PRECAUTION

Procedure to clear warning lights (When not clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle at 54 km/h (34 mph) or more for 3 seconds or more to clear the warning lights.





PROCEDURE

1.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH
a.

Replace the rear axle hub and bearing assembly RH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


Result:
Proceed to
NEXT



NEXT

END