Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C13807E  Stop Lamp Relay Actuator Stuck On  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.*

·

The dynamic radar cruise control system is operating and is applying the brakes.*

·

Secondary collision brake is operating.*

·

Brake hold is operating.

·

The parking brake is engaged while the vehicle is being driven.

*: w/ Pre-collision System



DTC No. Detection Item DTC Detection Condition Trouble Area
C13807E Stop Lamp Relay Actuator Stuck On When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is off, the signal at the STP2 terminal is different from the input signal at the STP terminal for 5 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light set



WIRING DIAGRAM

C401668E38
2.479,0.823 3.406,1.042 0.927,0.219 10 false to Each ECU 4.917,2.542 5.354,2.74 0.438,0.198 10 false STP 4.896,3.448 5.479,3.615 0.583,0.167 10 false STPO 4.917,4.438 5.417,4.719 0.5,0.281 10 false STP2 1.74,4.438 2.51,4.635 0.771,0.198 10 false GND 2.969,4.438 3.74,4.635 0.771,0.198 10 false OUT 2.958,3.438 3.479,3.635 0.521,0.198 10 false ACC 3.146,2.531 3.417,2.781 0.271,0.25 10 false L 1.26,6.344 2.031,6.542 0.771,0.198 10 false W13 1.271,6.5 3.708,6.833 2.438,0.333 10 false Rear Combination Light Assembly LH 1.26,7.875 2.031,8.073 0.771,0.198 10 false W12 5.052,7.875 5.823,8.073 0.771,0.198 10 false R47 4.729,5.177 5.25,5.375 0.521,0.198 10 false A34 4.719,5.323 6.26,5.875 1.542,0.552 10 false Skid Control ECU (Brake Actuator Assembly) 1.656,4.833 2.156,5.083 0.5,0.25 10 false A85 1.635,5 3.75,5.365 2.115,0.365 10 false Stop Light Switch Assembly 1.115,1.583 2.135,1.854 1.021,0.271 10 false from Battery 0.969,2.906 1.49,3.188 0.521,0.281 10 false STOP 1.75,2.865 2.021,3.115 0.271,0.25 10 false B 1.563,2.646 1.833,2.896 0.271,0.25 10 false 7 1.552,4.219 1.802,4.469 0.25,0.25 10 false 2 3.344,2.313 3.594,2.563 0.25,0.25 10 false 3 3.344,3.219 3.594,3.469 0.25,0.25 10 false 4 3.333,4.219 3.583,4.469 0.25,0.25 10 false 1 4.688,2.302 4.938,2.552 0.25,0.25 10 false 42 4.677,3.219 4.927,3.469 0.25,0.25 10 false 10 4.677,4.219 4.927,4.469 0.25,0.25 10 false 44 2.948,5.875 3.365,6.125 0.417,0.25 10 false 2 1.625,5.833 1.958,6.083 0.333,0.25 10 false 4 1.625,7.354 1.875,7.604 0.25,0.25 10 false 4 2.958,7.354 3.208,7.604 0.25,0.25 10 false 2 6.281,7.313 6.531,7.563 0.25,0.25 10 false 2 4.969,7.323 5.219,7.573 0.25,0.25 10 false 1 1.26,8.031 3.729,8.365 2.469,0.333 10 false Rear Combination Light Assembly RH 5.042,8.021 7.104,8.448 2.063,0.427 10 false Center Stop Light Set 1.292,2.667 1.542,2.917 0.25,0.25 10 false 2 0.938,2.667 1.188,2.917 0.25,0.25 10 false 1 1.833,6.104 2.167,6.354 0.333,0.25 10 false E 2.594,7.573 3.031,7.771 0.438,0.198 10 false STP 2.583,6.104 3.021,6.302 0.438,0.198 10 false STP 1.833,7.573 2.167,7.823 0.333,0.25 10 false E 6.104,7.573 6.438,7.823 0.333,0.25 10 false E 5.167,7.573 5.5,7.823 0.333,0.25 10 false B 2.177,6.125 2.615,6.323 0.438,0.198 10 false Stop 2.167,7.604 2.604,7.802 0.438,0.198 10 false Stop

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION



HINT:

When DTC P057111, P057112 and/or P057113 are output together with DTC C13807E, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.

P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>P057111

P057112: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>P057112

P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>P057113


PROCEDURE

1.CHECK STOP LIGHT ILLUMINATION STATUS
a.

With the brake pedal released, check the illumination status of the brake lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY CIRCUIT)

B

7.CHECK STOP LIGHT OPERATION
2.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY CIRCUIT)
a.
C440416C25
0.448,0.448 0.781,0.698 0.333,0.25 2.083,1.656 1.729,1.021 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.49 0.958,0.688 0.458,0.198 10 false A85 2.021,1.688 2.479,1.885 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-4 (ACC) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK STOP LIGHT ILLUMINATION STATUS

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY CIRCUIT)
3.CHECK STOP LIGHT ILLUMINATION STATUS
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A85 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Check the illumination status of the brake lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

4.CHECK STOP LIGHT ILLUMINATION STATUS

B

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK STOP LIGHT ILLUMINATION STATUS
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Check the illumination status of the brake lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY CIRCUIT)
a.
C440416C25
0.448,0.448 0.781,0.698 0.333,0.25 2.083,1.656 1.729,1.021 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.49 0.958,0.688 0.458,0.198 10 false A85 2.021,1.688 2.479,1.885 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-4 (ACC) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-4 (ACC) or A34-10 (STPO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

NG

9.CHECK STOP LIGHT OPERATION
8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)
a.
C399487C77
0.344,0.229 0.729,0.479 0.385,0.25 2.438,0.938 2.583,0.344 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.406,0.271 0.865,0.469 0.458,0.198 10 false A34 2.469,0.177 2.854,0.417 0.385,0.24 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-44 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK STOP LIGHT OPERATION
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

NG

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
C427377C05
0.333,0.448 0.75,0.698 0.417,0.25 0.896,1.74 1.521,1.344 true 0.396,0.49 0.781,0.698 0.385,0.208 10 false W13 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.583,1.729 1.042,1.927 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Rear Combination Light Assembly LH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W13-2 (STP) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE

w/o Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE


NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
C427377C06
0.333,0.448 0.75,0.698 0.417,0.25 0.969,1.74 1.521,1.333 true 0.385,0.49 0.771,0.698 0.385,0.208 10 false W12 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.74,1.76 1.198,1.958 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Rear Combination Light Assembly RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Disconnect the W12 rear combination light assembly RH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W12-2 (STP) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE

w/o Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE


NG

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
a.
C401718C15
0.281,0.365 0.656,0.615 0.375,0.25 1.188,1.594 1.604,1.177 true 0.344,0.396 0.802,0.594 0.458,0.198 10 false R47 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.073,1.594 1.229,1.792 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Center Stop Light Set)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Disconnect the W12 rear combination light assembly RH connector.


e.

Disconnect the R47 center stop light set connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R47-1 (B) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

13.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
13.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Disconnect the W12 rear combination light assembly RH connector.


e.

Disconnect the R47 center stop light set connector.


f.

Disconnect the A85 stop light switch assembly connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-1 (OUT) - W13-2 (STP) Always Below 1 Ω
A85-1 (OUT) or W13-2 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR