Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  P057112  Brake Switch "A" Circuit Short to Battery  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if either of the following occurs:

·

Stop light switch assembly stuck on malfunction.

·

The accelerator and brake pedals are depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
P057112 Brake Switch "A" Circuit Short to Battery The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.1 kgf/cm2, 72.5 psi) or less, and the stop light switch assembly is on for 60 seconds or more.
·

Stop light switch assembly

·

Stop light switch assembly installation

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

ECM

·

Shift lock control ECU (shift lock control unit assembly)

·

Certification ECU (smart key ECU assembly)*1

·

TCM*2



*1: w/ Smart Entry and Start System.

*2: for M20A-FKS.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PRECAUTION

Procedure to clear warning lights (When not clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle and depress the brake pedal 2 or 3 times to clear the warning lights.





PROCEDURE

1.CHECK BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height and stop light switch assembly installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)
a.
C440416C26
0.375,0.667 0.813,0.927 0.438,0.26 2.156,1.625 1.844,1 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.177,1.656 2.333,1.854 0.156,0.198 10 false L 0.479,0.708 0.969,1.042 0.49,0.333 10 false A85
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.
C439920C23
0.271,0.5 0.604,0.75 0.333,0.25 1.76,1.823 1.594,1.24 true 0.323,0.542 0.781,0.74 0.458,0.198 10 false A85 1.781,1.833 2,2.052 0.219,0.219 10 false L 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.
C439920C23
0.271,0.5 0.604,0.75 0.333,0.25 1.76,1.823 1.594,1.24 true 0.323,0.542 0.781,0.74 0.458,0.198 10 false A85 1.781,1.833 2,2.052 0.219,0.219 10 false L 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Disconnect the A23 ECM connector (for 2GR-FKS).


e.

Disconnect the A24 ECM connector (for A25A-FKS, M20A-FKS).


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C439920C23
0.271,0.5 0.604,0.75 0.333,0.25 1.76,1.823 1.594,1.24 true 0.323,0.542 0.781,0.74 0.458,0.198 10 false A85 1.781,1.833 2,2.052 0.219,0.219 10 false L 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Disconnect the A23 ECM connector (for 2GR-FKS).


e.

Disconnect the A24 ECM connector (for A25A-FKS, M20A-FKS).


f.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector (w/ Smart Entry and Start System).


g.

Disconnect the K28 shift lock control ECU (shift lock control unit assembly) connector (w/o Smart Entry and Start System).


h.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Always Below 1.5 V



Result:
Result Proceed to
OK A
NG (w/ Smart Entry and Start System) B
NG (for M20A-FKS without Smart Entry and Start System) C
NG (except M20A-FKS without Smart Entry and Start System) D



A

B

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
C439920C23
0.271,0.5 0.604,0.75 0.333,0.25 1.76,1.823 1.594,1.24 true 0.323,0.542 0.781,0.74 0.458,0.198 10 false A85 1.781,1.833 2,2.052 0.219,0.219 10 false L 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Disconnect the A23 ECM connector (for 2GR-FKS).


e.

Disconnect the A24 ECM connector (for A25A-FKS, M20A-FKS).


f.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector.


g.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


h.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Always Below 1.5 V



Result:
Result Proceed to
OK A
NG (for M20A-FKS) B
NG (for 2GR-FKS, A25A-FKS) C



A

REPLACE SMART KEY ECU ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.
C439920C23
0.271,0.5 0.604,0.75 0.333,0.25 1.76,1.823 1.594,1.24 true 0.323,0.542 0.781,0.74 0.458,0.198 10 false A85 1.781,1.833 2,2.052 0.219,0.219 10 false L 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Disconnect the A24 ECM connector.


e.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector.


f.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


g.

Disconnect the C111 TCM connector.


h.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.
C439920C23
0.271,0.5 0.604,0.75 0.333,0.25 1.76,1.823 1.594,1.24 true 0.323,0.542 0.781,0.74 0.458,0.198 10 false A85 1.781,1.833 2,2.052 0.219,0.219 10 false L 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A85 stop light switch assembly connector.


d.

Disconnect the A24 ECM connector.


e.

Disconnect the K28 shift lock control ECU (shift lock control unit assembly) connector.


f.

Disconnect the C111 TCM connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR