Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C14E914  Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C051212

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C051212

DTC No. Detection Item DTC Detection Condition Trouble Area
C14E914 Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open An open or short in the speed sensor power supply circuit is detected for 0.12 seconds or more.
·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Wire harness or connector

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Skid control ECU (brake actuator assembly)



DTC Detection Conditions: C14E914
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status An open in the speed sensor power supply circuit is detected. ○ -
A short in the speed sensor power supply circuit is detected. - ○
Detection Time 0.12 seconds or more. 0.12 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
a.
C447247C21
0.354,0.677 0.74,0.948 0.385,0.271 2.083,1.75 1.844,1.146 true 1.417,1.75 1.594,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.469,0.729 0.781,0.927 0.313,0.198 10 false u2 2.021,1.802 2.417,2.021 0.396,0.219 10 false RA+ 1.313,1.792 1.708,2.01 0.396,0.219 10 false RA-
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
(to Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the u2 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
u2-2 (RA+) - u2-1 (RA-) Ignition switch on 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
a.
C456826C02
0.49,0.75 0.906,1.042 0.417,0.292 1.438,1.729 1.604,1.229 true 2.073,1.729 1.823,1.229 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.583,0.823 1.042,1.021 0.458,0.198 10 false uR1 1.344,1.771 1.802,1.969 0.458,0.198 10 false RR- 2.021,1.771 2.479,1.969 0.458,0.198 10 false RR+
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the uR1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uR1-1 (RR+) - uR1-2 (RR-) Ignition switch on 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the uR1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uR1-1 (RR+) or A34-22 (RR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR