Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2021.02
RM33A0E _58 Vehicle Interior _065385 SEAT _0328606 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a slide motor position sensor signal despite the seat having been moved forward or backward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2650 Slide Sensor Malfunction Slide motor position sensor signal not received when power seat moved forward or backward
·

Position control ECU assembly (driver seat)

·

Slide motor (Upper seat track rail sub-assembly (driver seat))

·

Wire harness or connector



WIRING DIAGRAM

B502438E34
0.5,3.188 3.302,3.406 2.802,0.219 10 false Front Seat Adjuster Assembly (Driver Seat) 0.823,2.281 1.823,2.521 1,0.24 10 false b19 0.823,2.469 2.979,2.865 2.156,0.396 10 false Slide Motor (Upper Seat Track Rail Sub-assembly (Driver Seat)) 2.198,0.396 2.354,0.594 0.156,0.198 10 false 4 2.198,0.906 2.354,1.104 0.156,0.198 10 false 1 2.208,1.417 2.365,1.615 0.156,0.198 10 false 2 2.198,1.938 2.354,2.135 0.156,0.198 10 false 3 5.229,0.51 5.844,0.708 0.615,0.198 10 false SLD+ 5.229,1.021 5.844,1.219 0.615,0.198 10 false SLD- 5.219,1.542 5.833,1.74 0.615,0.198 10 false SSRS 5.229,2.063 5.844,2.26 0.615,0.198 10 false SENG 4.885,0.281 5.281,0.479 0.396,0.198 10 false 1 4.885,0.823 5.344,1.021 0.458,0.198 10 false 5 4.854,1.323 5.469,1.521 0.615,0.198 10 false 26 4.844,1.844 5.458,2.042 0.615,0.198 10 false 12 4.823,1.052 5.281,1.25 0.458,0.198 10 false b23 4.823,0.531 5.281,0.729 0.458,0.198 10 false b23 4.813,2.073 5.271,2.271 0.458,0.198 10 false b25 4.823,1.563 5.281,1.76 0.458,0.198 10 false b25 4.75,2.625 6.719,3.198 1.969,0.573 10 false Position Control ECU Assembly (Driver Seat)

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2650 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Slide motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)

NG

7.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)
a.

Disconnect the b19 slide motor (front seat adjuster assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b19-2 - b19-3 Slide switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))
5.CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))
a.
B517917C79
1.51,0.167 1.927,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.594,0.198 2.052,0.396 0.458,0.198 10 false b19
*a Component with harness connected
(Slide Motor (Front Seat Adjuster Assembly (Driver Seat))


Reconnect the b19 slide motor (front seat adjuster assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b19-2 - Body ground Slide motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPLACE SLIDE MOTOR (UPPER SEAT TRACK RAIL SUB-ASSEMBLY (DRIVER SEAT))

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the b25 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b25-26 (SSRS) - b19-2 Always Below 1 Ω
b25-26 (SSRS) or b19-2 - Body ground Always 10 kΩ or higher
b25-12 (SENG) - b19-3 Always Below 1 Ω
b25-12 (SENG) or b19-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))
a.

Remove the slide motor (front seat adjuster assembly (driver seat)).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the slide motor (front seat adjuster assembly (driver seat)).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))

NG

REPLACE SLIDE MOTOR (UPPER SEAT TRACK RAIL SUB-ASSEMBLY (DRIVER SEAT))

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the b23 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b23-1 (SLD+) - b19-4 Always Below 1 Ω
b23-1 (SLD+) or b19-4 - Body ground Always 10 kΩ or higher
b23-5 (SLD-) - b19-1 Always Below 1 Ω
b23-5 (SLD-) or b19-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR