Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065374 NAVIGATION / MULTI INFO DISPLAY _0328126 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15DB  Telematics Transceiver Disconnected  


DESCRIPTION

If the radio and display receiver assembly cannot detect the telematics transceiver for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past telematics transceiver recognition information (registered information), this DTC will be stored.

The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DB Telematics Transceiver Disconnected Telematics transceiver disconnected
·

Harness or connector

·

Telematics transceiver

·

Telematics transceiver power source circuit

·

Radio and display receiver assembly

·

Navigation ECU



HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E433089E11
2.75,0.344 3.208,0.542 0.458,0.198 10 false K156 2.75,1.25 3.208,1.448 0.458,0.198 10 false K156 2.75,2.063 3.208,2.26 0.458,0.198 10 false K156 4.25,0.333 4.708,0.531 0.458,0.198 10 false g2 4.25,0.813 4.708,1.01 0.458,0.198 10 false g2 4.26,1.292 4.719,1.49 0.458,0.198 10 false g2 4.167,2.385 4.625,2.583 0.458,0.198 10 false K156 4.188,2.865 4.646,3.063 0.458,0.198 10 false K156 3.208,0.333 3.667,0.531 0.458,0.198 10 false +B 3.198,1.25 3.656,1.448 0.458,0.198 10 false IG2 3.219,2.063 3.677,2.26 0.458,0.198 10 false E 3.677,0.344 4.135,0.542 0.458,0.198 10 false USB+ 3.698,0.823 4.156,1.021 0.458,0.198 10 false USB- 3.656,1.292 4.115,1.49 0.458,0.198 10 false UGBS 3.677,2.375 4.135,2.573 0.458,0.198 10 false USBV 3.667,2.854 4.125,3.052 0.458,0.198 10 false USBG 5.708,2.385 6.167,2.583 0.458,0.198 10 false USBV 5.708,2.865 6.167,3.063 0.458,0.198 10 false USBG 1.49,0.51 1.948,0.708 0.458,0.198 10 false DCM 1.208,1.406 2.302,1.625 1.094,0.219 10 false ECU-IG2 NO. 3 0.135,0.323 0.99,0.552 0.854,0.229 10 false from Battery 0.01,1.25 0.979,1.719 0.969,0.469 10 false from IG2-NO. 2 Relay 0.74,3.208 2.583,3.479 1.844,0.271 10 false : USB Communication Line 2.927,3.177 4.927,3.385 2,0.208 10 false Telematics Transceiver 5.51,3.292 6.729,3.729 1.219,0.438 10 false Radio and Display Receiver Assembly 5.646,1.792 6.729,2.073 1.083,0.281 10 false Navigation ECU 5.635,1.604 6.094,1.802 0.458,0.198 10 false g6 5.51,3.125 5.969,3.323 0.458,0.198 10 false K1 2.865,0.135 3.104,0.365 0.24,0.229 10 false 1 2.823,1.031 3.063,1.26 0.24,0.229 10 false 19 2.854,1.844 3.094,2.073 0.24,0.229 10 false 20 4.292,0.146 4.531,0.375 0.24,0.229 10 false 2 4.292,0.615 4.531,0.844 0.24,0.229 10 false 1 4.302,1.094 4.542,1.323 0.24,0.229 10 false 3 4.26,2.167 4.74,2.573 0.479,0.406 10 false 15 4.271,2.667 4.51,2.896 0.24,0.229 10 false 31 5.458,2.75 5.698,2.979 0.24,0.229 10 false 11 5.458,2.281 5.698,2.51 0.24,0.229 10 false 10 5.531,1.177 5.771,1.406 0.24,0.229 10 false 3 5.531,0.698 5.771,0.927 0.24,0.229 10 false 2 5.531,0.198 5.771,0.427 0.24,0.229 10 false 1 0.688,2.865 1.51,3.094 0.823,0.229 10 false *: Shielded 5.719,0.365 6.177,0.563 0.458,0.198 10 false USB+ 5.708,0.844 6.167,1.042 0.458,0.198 10 false USB- 5.719,1.313 6.177,1.51 0.458,0.198 10 false UGBS 5.094,1.021 5.917,1.25 0.823,0.229 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 90 seconds.


d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER POWER SOURCE)
a.

Disconnect the K156 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K156-20 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K156-1 (+B) - K156-20 (E) Always 11 to 14 V
K156-19 (IG2) - K156-20 (E) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the K1 radio and display receiver assembly connector.


b.
E367494C99
1.542,0.75 1.958,1.021 0.417,0.271 2.438,2.844 1.844,2.052 false 1.26,2.813 1.531,2.052 false 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 1.667,0.802 2.063,1.063 0.396,0.26 10 false K1 2.292,2.875 2.906,3.073 0.615,0.198 10 false USBV 1.021,2.875 1.635,3.073 0.615,0.198 10 false USBG
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-11 (USBG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K1-10 (USBV) - K1-11 (USBG) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the K1 radio and display receiver assembly connector.


b.

Disconnect the K156 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-10 (USBV) - K156-15 (USBV) Always Below 1 Ω
K1-11 (USBG) - K156-31 (USBG) Always Below 1 Ω
K1-10 (USBV) or K156-15 (USBV) - Body ground Always 10 kΩ or higher
K1-11 (USBG) or K156-31 (USBG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)
a.

Disconnect the g2 telematics transceiver connector.


b.

Disconnect the g6 navigation ECU connector.


c.
E427772C95
1.479,0.302 1.927,0.583 0.448,0.281 1.458,2.563 1.906,2.844 0.448,0.281 2.417,0.635 2.229,0.635 2.229,0.635 1.813,1.302 true 1.583,3.406 1.292,2.969 1.292,2.969 1.156,2.969 true 2.208,2.969 2.083,2.969 2.083,2.969 1.813,3.396 true 2.156,4.031 2.01,4.031 2.01,4.031 1.76,3.573 true 1.573,1.302 1.167,0.635 1.167,0.635 0.958,0.635 true 1.365,2.01 1.479,2.01 1.479,2.01 1.708,1.552 true 1.115,0.156 1.427,0.354 0.313,0.198 10 false *a 1.094,2.448 1.406,2.646 0.313,0.198 10 false *b 1.625,0.354 2.083,0.552 0.458,0.198 10 false g2 1.615,2.615 2.073,2.813 0.458,0.198 10 false g6 0.583,0.552 1.198,0.75 0.615,0.198 10 false USB- 0.719,2.875 1.333,3.073 0.615,0.198 10 false USB+ 2.479,0.563 3.094,0.76 0.615,0.198 10 false USB+ 2.271,2.896 2.885,3.094 0.615,0.198 10 false USB- 2.219,3.969 2.833,4.167 0.615,0.198 10 false UGBS 0.938,1.927 1.552,2.125 0.615,0.198 10 false UGBS
*a Front view of wire harness connector
(to Telematics Transceiver)
*b Front view of wire harness connector
(to Navigation ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g2-2 (USB+) - g6-1 (USB+) Always Below 1 Ω
g2-1 (USB-) - g6-2 (USB-) Always Below 1 Ω
g2-3 (UGBS) - g6-3 (UGBS) Always Below 1 Ω
g2-2 (USB+) or g6-1 (USB+) - Body ground Always 10 kΩ or higher
g2-1 (USB-) or g6-2 (USB-) - Body ground Always 10 kΩ or higher
g2-3 (UGBS) or g6-3 (UGBS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and wait for 90 seconds.


e.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

NG

7.CHECK NAVIGATION ECU
7.CHECK NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and wait for 90 seconds.


e.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY