Home › General › MAINTENANCE › UB80E AUTOMATIC TRANSAXLE FLUID › from 2021.02
RM33A0E _V1 General _065356 MAINTENANCE _0327045 UB80E AUTOMATIC TRANSAXLE FLUID A

MAINTENANCE  UB80E AUTOMATIC TRANSAXLE FLUID  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during automatic transaxle fluid replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 53851M 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 6.REPLACE AUTOMATIC TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.
C370800

Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2]


c.
C370801

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. [#3]


d.
C370802C01
2.75,0.844 2.865,0.844 false 2.573,0.74 2.771,0.958 0.198,0.219 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. [#4]


e.
C370803

Measure the amount of automatic transaxle fluid drained. [#5]

HINT:

Add the same amount of automatic transaxle fluid in step [#8].



f.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing. [#6]

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


g.
C370801

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing. [#7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



h.
C370804

Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]

NOTICE:

Use Toyota Genuine ATF WS.



i.
C370800

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



j.

Lower the vehicle. [#10]


k.

Start the engine. [#11]


l.

Slowly move the shift lever from P to D, and then back to P. [#12]

HINT:
·

Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

·

Keep the shift lever in each position for approximately 3 seconds.




m.

Allow the engine to idle for 30 seconds to warm it up. [#13]


n.

Turn the engine switch off. [#14]


o.

Repeat steps [#1] to [#14].


p.

Repeat steps [#1] to [#10].


Hide 7.ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

Hide 8.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

Hide 9.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

Hide 53737B 12.INSTALL FRONT FENDER APRON SEAL LH

Hide 13.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 15.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 16.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH