Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE › from 2021.02
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0321820 TRANSMISSION WIRE A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL LH

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 3.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53737B 6.REMOVE FRONT FENDER APRON SEAL LH

Hide 7.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C370800

Remove the refill plug and gasket from the automatic transaxle case sub-assembly.


b.
C370801

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.


c.
C370802C01
2.75,0.844 2.865,0.844 false 2.573,0.74 2.771,0.958 0.198,0.219 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.


d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



f.

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



Hide 17650H 8.REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System)

Hide 51227B 10.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

Hide 32901C 11.SEPARATE OIL COOLER UNION SUB-ASSEMBLY

a.
C376181C01
1.396,1.948 1.563,1.948 1.563,1.948 1.802,1.531 true 1.198,1.865 1.375,2.063 0.177,0.198 10 true *1
*1 Oil Cooler Union Bolt


Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.


b.

Remove the oil cooler union bolt and 2 gaskets to separate the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.


Hide 35151F 12.REMOVE TRANSMISSION CASE SIDE COVER

a.
C369210

Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.


Hide 82125J 13.REMOVE TRANSMISSION WIRE

a.
C376919

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C361008C01
0.135,0.208 0.448,0.365 0.313,0.156 10 false *a 0.615,3.229 0.927,3.385 0.313,0.156 10 false *b
*a Connector (A)
*b Connector (B)


Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.


c.

Disconnect the 9 solenoid valve connectors.

HINT:
·

Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.

·

Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.




d.
C361010

Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.


e.
C374489

Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


f.
C361015

Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.