The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake actuator assembly) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU (brake actuator assembly). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU (brake actuator assembly). The pulse signal is created by switching the transistor in the skid control ECU (brake actuator assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU (brake actuator assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.
*: This vehicle speed signal is created by the skid control ECU (brake actuator assembly). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
This procedure is based on the premise that no devices connected to the optional connector is malfunctioning. Before performing this procedure, confirm that no devices connected to the optional connector is malfunctioning.
Before replacing the ECM, certification ECU (smart key ECU assembly)*, refer to Service Bulletin.
*: w/ Smart Entry and Start System
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the K21 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-6 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Connect the K21 combination meter assembly connector.
Disconnect the A34 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-34 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
Check the input waveform.
Connect the A34 skid control ECU (brake actuator assembly) connector.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal K21-5 (SI) and body ground.
Turn the ignition switch to ON.
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester connection | K21-5 (SI) - Body ground |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON, wheel being rotated |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
Disconnect the K21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-34 (SP1) - K21-5 (SI) | Always | Below 1 Ω |
| A34-34 (SP1) or K21-5 (SI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 ECM connector.*1
Disconnect the A23 ECM connector.*2
Disconnect the K3 radio and display receiver assembly connector.*4
Disconnect the K62 certification ECU (smart key ECU assembly) connector.*5
Disconnect the K17 navigation ECU connector.*6
Disconnect the K10 stereo component amplifier assembly connector.*7
Disconnect the K158 option connector.*3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-6 (+S) - Body ground | Always | 10 kΩ or higher |
Connect the A24 ECM connector.*1
Connect the A23 ECM connector.*2
Connect the K3 radio and display receiver assembly connector.*4
Connect the K62 certification ECU (smart key ECU assembly) connector.*5
Connect the K17 navigation ECU connector.*6
Connect the K10 stereo component amplifier assembly connector.*7
*1: except 2GR-FKS
*2: for 2GR-FKS
*3: w/o Radio and Display Receiver Assembly
*4: w/ Radio and Display Receiver Assembly
*5: w/ Smart Entry and Start System
*6: w/ Navigation System
*7: for 9 Speakers
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/o Navigation System | B |
A
B
Disconnect the K17 navigation ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-6 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the navigation ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Radio and Display Receiver Assembly | A |
| w/o Radio and Display Receiver Assembly | B |
A
B
Disconnect the K3 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-6 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the radio and display receiver assembly.
| Result |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 9 Speakers | A |
| except 9 Speakers | B |
A
B
Disconnect the K10 stereo component amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-6 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Smart Entry and Start System | A |
| w/o Smart Entry and Start System | B |
A
B
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-6 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the certification ECU (smart key ECU assembly).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL