Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the antenna divider*1 or navigation antenna assembly*2.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
·

Antenna divider*1

·

Navigation antenna assembly*2

·

Antenna cord sub-assembly (for Front Side)

·

Radio and display receiver assembly


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
·

Antenna divider*1

·

Navigation antenna assembly*2

·

Antenna cord sub-assembly (for Front Side)

·

Radio and display receiver assembly



*1: for LHD with Telematics Transceiver

*2: for LHD without Telematics Transceiver or RHD


WIRING DIAGRAM

for LHD with Telematics Transceiver
E388524E19
1.771,0.729 1.927,0.927 0.156,0.198 10 false 2 5.323,0.729 5.479,0.927 0.156,0.198 10 false 1 3.583,1.281 3.74,1.479 0.156,0.198 10 false * 0.917,1.323 1.073,1.521 0.156,0.198 10 false A 0.917,1.49 3.208,1.688 2.292,0.198 10 false Antenna Divider 5.365,1.531 7.063,1.958 1.698,0.427 10 false Radio and Display Receiver Assembly 5.365,1.354 5.521,1.552 0.156,0.198 10 false B 2.042,2.177 5.354,2.406 3.313,0.229 10 false *: Antenna Cord Sub-assembly (for Front Side)

for LHD without Telematics Transceiver or RHD
E388524E20
1.771,0.729 1.927,0.927 0.156,0.198 10 false 3 5.323,0.729 5.479,0.927 0.156,0.198 10 false 1 3.583,1.281 3.74,1.479 0.156,0.198 10 false * 0.917,1.333 1.073,1.531 0.156,0.198 10 false A 0.917,1.49 3.208,1.688 2.292,0.198 10 false Navigation Antenna Assembly 5.385,1.5 7.083,1.927 1.698,0.427 10 false Radio and Display Receiver Assembly 5.385,1.323 5.542,1.521 0.156,0.198 10 false B 2.042,2.177 5.354,2.406 3.313,0.229 10 false *: Antenna Cord Sub-assembly (for Front Side)

CAUTION / NOTICE / HINT

NOTICE:

Check that the antenna cord sub-assembly is properly installed and does not have any sharp bends, pinching or loose connections before performing following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (for LHD with Telematics Transceiver) B
NG (for LHD without Telematics Transceiver or RHD) C



A

B

2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Front Side)

C

4.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Front Side)
2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Front Side)
a.

Remove the antenna cord sub-assembly (for Front Side).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E437930C02
1.5,0.333 1.917,0.583 0.417,0.25 0.688,3.458 1.104,3.708 0.417,0.25 1.177,2.021 1.177,1.479 true 2.458,3.979 1.906,3.792 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.677,0.375 1.833,0.573 0.156,0.198 10 false A 1.125,2.063 1.438,2.26 0.313,0.198 10 false 2a 0.844,3.49 1,3.688 0.156,0.198 10 false B 2.531,3.906 2.844,4.104 0.313,0.198 10 false 1a
*a Component without harness connected
(Antenna Cord Sub-assembly (for Front Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-1 Always Below 1 Ω
A-2a - B-1a Always Below 1 Ω
A-2 or B-1 - Body ground Always 10 kΩ or higher
A-2a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ANTENNA DIVIDER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Front Side)

3.INSPECT ANTENNA DIVIDER
a.

b.
E241596C22
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.979,1.406 1.833,1.75 1.833,1.75 1.635,1.75 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.438,1.656 1.865,1.833 0.427,0.177 10 false 2a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 Always 10 kΩ or higher
2 - 2a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Front Side)
a.

Remove the antenna cord sub-assembly (for Front Side).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E322997C10
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.76 2.344,3.344 false 1.854,1 2.271,0.583 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.656,1.229 0.969,1.427 0.313,0.198 10 false A 0.813,3.521 1.125,3.719 0.313,0.198 10 false B
*a Component without harness connected
(Antenna Cord Sub-assembly (for Front Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-3a - B-1a Always Below 1 Ω
A-3 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Front Side)

5.INSPECT NAVIGATION ANTENNA ASSEMBLY


Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG