| Battery terminal is disconnected/reconnected
|
Perform steering sensor zero point calibration
|
Lane Tracing Assist System
|
( )
|
| Pre-collision system
|
| Memorize steering angle neutral point
|
Parking assist monitor system
|
( )
|
| Panoramic View Monitor System
|
( )
|
| Replacement of ECM
|
Perform Vehicle Identification Number (VIN) or frame number registration
|
MIL comes on
|
w/ Canister Pump Module:( )
w/o Canister Pump Module:( )
|
| Perform code registration (Immobiliser system)
|
Engine start function
|
See Service Bulletin for the registration method
|
·
Replacement of engine assembly
·
Gas leak from exhaust system is repaired
·
Replacement of throttle body with motor assembly
·
Replacement of cam timing control motor with EDU assembly
·
Removal and installation of a cam timing control motor with EDU assembly
·
Replacement of camshaft timing gear assembly
·
Removal and installation of a camshaft timing gear assembly
·
Replacement of cylinder head sub-assembly
·
Replacement of camshaft (for intake or exhaust camshaft)
·
Replacement of camshaft timing exhaust gear assembly
·
Replacement of port fuel injector assembly
·
Replacement of direct fuel injector assembly
·
Replacement of fuel pump assembly (for high pressure side)
·
Replacement of engine coolant temperature sensor
·
Replacement of spark plug
·
Replacement of ignition coil assembly
·
Replacement of EGR valve assembly
·
Replacement of knock control sensor
·
Replacement of air fuel ratio sensor (sensor 2)
|
Inspection After Repair
|
·
Engine start function, etc.
|
w/ Canister Pump Module:( )
w/o Canister Pump Module:( )
|
| Replacement of automatic transaxle assembly
|
2.
Input transaxle compensation code into ECM
3.
Perform road test to allow ECM to learn
|
·
Deterioration of fuel efficiency
|
( )for UB80E Initialization
( )for UB80E Registration
|
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
|
2.
Transfer transaxle compensation code
3.
Perform road test to allow ECM to learn
|
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
|
2.
Reset transaxle compensation code
3.
Perform road test to allow ECM to learn
|
| Replacement of ECM*2
|
Perform code registration (Immobiliser function)
|
·
Wireless door lock control system
·
Smart Entry and Start System (for Entry Function)
·
Smart Entry and Start System (for Start Function)
|
See Service Bulletin for the registration method
|
| Replacement of ECM*3
|
Perform code registration (Immobiliser system)
|
·
Wireless Door Lock Control System
|
See Service Bulletin for the registration method
|
| Replacement of automatic transaxle fluid
|
ATF thermal degradation estimate reset
|
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
|
( )
|
| Replacement of front bumper assembly
|
Front television camera view adjustment
|
Panoramic view monitor system
|
( )for Initialization
( )for Calibration
|
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
|
·
Television camera controller initialization
·
Rear television camera assembly optical axis (Back camera position setting)
|
| Rear television camera assembly optical axis (Back camera position setting)
|
Parking assist monitor system
|
( )for Initialization
( )for Calibration
|
| Perform headlight ECU sub-assembly LH initialization
|
Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System)
|
( )
|
·
Measure ultrasonic sensor detection angle
·
Ultrasonic sensor detection angle registration
|
Parking Support Brake System
|
( )
|
| Front wheel alignment adjustment
|
2.
Perform acceleration sensor zero point calibration and system information memorization.
|
·
VSC disabled or malfunctioning
·
Slip indicator light illuminated
·
ABS warning light illuminated
|
( )
|
| Replacement of front bumper assembly
|
·
Measure ultrasonic sensor detection angle
·
Ultrasonic sensor detection angle registration
|
Parking Support Brake System
|
( )
|