Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR SEAT SIDE AIRBAG ASSEMBLY (for Reclining Seat Type) › from 2021.02
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0352092 REAR SEAT SIDE AIRBAG ASSEMBLY(for Reclining Seat Type) A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR SEAT SIDE AIRBAG ASSEMBLY(for Reclining Seat Type)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane tracing assist system (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
B394719

·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If a rear seat airbag assembly has been deployed, replace the rear seat airbag assembly, rear side seatback frame sub-assembly, rear side seatback pad and rear side seatback cover sub-assembly with the necessary parts in accordance with the extent of the collision damage.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>DISASSEMBLY


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73350C 3.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 72693 5.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 71940A 6.REMOVE REAR SEAT HEADREST ASSEMBLY

Hide 62332A 9.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear side seatback assembly.


Hide 10.REMOVE REAR SIDE SEATBACK ASSEMBLY

Hide 11.REMOVE REAR SIDE SEATBACK COVER WITH PAD

Hide 73940A 12.REMOVE REAR SEAT AIRBAG ASSEMBLY

CAUTION:
B399378C03
0.615,0.531 0.771,0.729 0.156,0.198 10 false .
V100155

Deployment Side


When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.


a.
B490714

Disengage the clamp.


b.

Disconnect the wire harness from the wire harness clamp.


c.

Remove the 2 nuts and rear seat airbag assembly.

NOTICE:
·

Do not reuse the nuts.

·

Make sure that the rear side seatback frame sub-assembly is not deformed. If it is deformed, replace the rear side seatback frame sub-assembly with a new one.