Home › Engine / Hybrid System › 2GR-FKS (LUBRICATION) › OIL PUMP › from 2021.02
RM33A0E _51 Engine / Hybrid System _065338 2GR-FKS LUBRICATION _0328793 OIL PUMP A

2GR-FKS LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during timing chain cover assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

Hide 11310 3.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A369463C01
0.719,2.854 1.031,3.01 0.313,0.156 10 false *a 2.531,2.74 2.844,2.896 0.313,0.156 10 false *a
*a Nut


w/ Stud Bolt:

i.

Remove the 23 bolts and 2 nuts shown in the illustration.



b.
A457607

w/o Stud Bolt:

i.

Remove the 25 bolts shown in the illustration.



c.
A369464C01
0.542,1.698 1.583,4.323 1.583,4.323 2.688,3.052 true 0.594,2.927 1.573,4.333 1.573,4.333 2.427,3.958 true 1.094,4.083 1.563,4.333 true 1.5,4.375 1.813,4.531 0.313,0.156 10 false *a
*a Protective Tape


Remove the timing chain cover assembly by prying between the timing chain cover assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover assembly.



d.
A369465

Remove the oil pump gasket from the cylinder block sub-assembly.