Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › from 2021.02
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0327773 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Front door glass sub-assembly

·

Front door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 74038A 4.REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Hide 5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 74220 7.REMOVE FRONT ARMREST ASSEMBLY

Hide 81230 8.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 10.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Hide 67832 11.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68102 12.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67856B 13.REMOVE FRONT DOOR PANEL PROTECTOR

Hide 68151C 14.REMOVE FRONT DOOR GLASS RUN

Hide 67404F 15.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 69220 16.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Hide 17.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 69040A 18.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B469768C01
2.99,2.896 2.813,2.552 false 2.948,2.906 3.26,3.104 0.313,0.198 10 false *1
*1 Front Door Lock Open Rod
V113147

Remove in this Direction


Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws.


c.

Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.


d.

When reusing the front door lock with motor assembly:

i.
B469770

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69036A 19.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY

a.
B469771

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B469772C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.


Hide 69720B 20.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B469773C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760C 21.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B469774C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inside locking cable assembly as shown in the illustration.