Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2021.02–2022.01
RM33A0E _59 Vehicle Exterior _065393 MIRROR (EXT) _0327399 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors to adjust the mirror surface position.

WIRING DIAGRAM

B490273E27
2.719,1.354 3.281,1.604 0.563,0.25 10 false MIRB 1.427,1.344 1.99,1.594 0.563,0.25 10 false M+ 1.271,2.01 1.833,2.26 0.563,0.25 10 false MSW 1.51,2.688 2.073,2.938 0.563,0.25 10 false E 0.479,3.396 1.438,3.635 0.958,0.24 10 false O25 0.49,3.563 1.708,3.927 1.219,0.365 10 false Outer Mirror Switch Assembly 0.719,4.229 2.552,4.49 1.833,0.26 10 false : CAN Communication Line 2.469,3.375 3.031,3.625 0.563,0.25 10 false K53 2.469,3.542 4.115,3.927 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.115,1.479 6.677,1.865 1.563,0.385 10 false Outer Mirror Control ECU Assembly (Driver Door) 1.698,1.24 2.073,1.594 0.375,0.354 10 false 4 1.708,1.917 2.094,2.271 0.385,0.354 10 false 5 1.698,2.573 2.083,2.917 0.385,0.344 10 false 7 2.521,2.573 3.083,2.823 0.563,0.25 10 false 9 2.5,1.906 3.063,2.156 0.563,0.25 10 false 8 2.5,1.24 3.063,1.49 0.563,0.25 10 false 7 4.823,3.917 7.031,4.615 2.208,0.698 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 2.719,2.01 3.281,2.26 0.563,0.25 10 false MIRS 2.719,2.667 3.281,2.917 0.563,0.25 10 false MIRE

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system and LIN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON OFF: Mirror select switch off
ON: Mirror select switch R switch on
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON OFF: Mirror select switch off
ON: Mirror select switch L switch on
-
Mirror Position SW (R) Mirror adjust switch signal (Right) OFF or ON OFF: Mirror adjust switch not pushed right
ON: Mirror adjust switch pushed right
Check with the mirror select switch L or R selected
Mirror Position SW (L) Mirror adjust switch signal (Left) OFF or ON OFF: Mirror adjust switch not pushed left
ON: Mirror adjust switch pushed left
Check with the mirror select switch L or R selected
Mirror Position SW (Up) Mirror adjust switch signal (Up) OFF or ON OFF: Mirror adjust switch not pushed up
ON: Mirror adjust switch pushed up
Check with the mirror select switch L or R selected
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) OFF or ON OFF: Mirror adjust switch not pushed down
ON: Mirror adjust switch pushed down
Check with the mirror select switch L or R selected
Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 98,99,100,101,102,103
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT OUTER MIRROR SWITCH ASSEMBLY
2.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the O25 outer mirror switch assembly.


b.

Disconnect the K53 main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O25-7 (E) - K53-9 (MIRE) Always Below 1 Ω
O25-4 (M+) - K53-7 (MIRB) Always Below 1 Ω
O25-5 (MSW) - K53-8 (MIRS) Always Below 1 Ω
O25-7 (E) or K53-9 (MIRE) - Body ground Always 10 kΩ or higher
O25-4 (M+) or K53-7 (MIRB) - Body ground Always 10 kΩ or higher
O25-5 (MSW) or K53-8 (MIRS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR