Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › from 2021.02
RM33A0E _59 Vehicle Exterior _065393 MIRROR (EXT) _0327399 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirrors do not Return to Memorized Position  


DESCRIPTION

If any of the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. The main body ECU (multiplex network body ECU) sends the reproduction signal to each outer mirror control ECU assembly via CAN communication. When receiving the reproduction signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly, to adjust the mirror surface to the stored position.

WIRING DIAGRAM

B490274E11
0.073,5.583 1.708,6 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.448,8.271 2.208,8.531 1.76,0.26 10 false : CAN Communication Line 2.302,7.573 3.063,7.844 0.76,0.271 10 false N10 3.469,7.198 4.01,7.427 0.542,0.229 10 false RE1 3.354,6.719 3.896,6.948 0.542,0.229 10 false HSSR 3.448,6.25 3.99,6.479 0.542,0.229 10 false RVC 3.354,5.771 3.896,6 0.542,0.229 10 false VSSR 2.542,4.771 4.104,5.188 1.563,0.417 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.219,4.552 5.76,4.781 0.542,0.229 10 false O18 4.802,7.542 5.792,7.802 0.99,0.26 10 false N23*1, N24*2 4.802,7.719 6.875,8.26 2.073,0.542 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 3.833,7.083 4.375,7.313 0.542,0.229 10 false 14 3.833,6.625 4.375,6.854 0.542,0.229 10 false 13 3.844,6.146 4.385,6.375 0.542,0.229 10 false 5 3.833,5.667 4.375,5.896 0.542,0.229 10 false 6 6.385,4.177 6.927,4.406 0.542,0.229 10 false E 2.302,7.729 4.51,8.583 2.208,0.854 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.917,3.25 4.458,3.479 0.542,0.229 10 false O8 3.906,0.563 4.448,0.792 0.542,0.229 10 false O9 3.552,3.25 4.094,3.479 0.542,0.229 10 false M1 5.219,4.708 6.771,4.969 1.552,0.26 10 false Seat Memory Switch 4.844,2.365 5.958,2.646 1.115,0.281 10 false O21*1, O22*2 4.833,2.521 6.885,3.01 2.052,0.49 10 false Outer Rear View Mirror Assembly (Driver Door) 5.76,0.813 6.271,1.229 0.51,0.417 10 false Vertical Sensor 5.375,1.76 6.542,1.99 1.167,0.229 10 false Horizontal Sensor 3.344,0.573 3.885,0.802 0.542,0.229 10 false VSSR 3.448,1.042 3.99,1.271 0.542,0.229 10 false LVC 3.344,1.542 3.885,1.771 0.542,0.229 10 false HSSR 3.49,2.021 4.031,2.25 0.542,0.229 10 false LE1 5.021,0.479 5.563,0.708 0.542,0.229 10 false VSRL 5.031,0.958 5.573,1.188 0.542,0.229 10 false VC 5.021,1.438 5.563,1.667 0.542,0.229 10 false HSRL 5.031,1.896 5.573,2.125 0.542,0.229 10 false E1 3.542,3.75 4.083,3.979 0.542,0.229 10 false M2 3.5,4.271 4.042,4.5 0.542,0.229 10 false MM 5.219,3.167 5.76,3.396 0.542,0.229 10 false 1 5.229,3.656 5.771,3.885 0.542,0.229 10 false 2 5.219,4.167 5.76,4.396 0.542,0.229 10 false MMRY 3.917,3.75 4.458,3.979 0.542,0.229 10 false O8 3.906,4.271 4.448,4.5 0.542,0.229 10 false O8 3.906,1.042 4.448,1.271 0.542,0.229 10 false O9 3.917,1.531 4.458,1.76 0.542,0.229 10 false O9 3.906,2.01 4.448,2.24 0.542,0.229 10 false O9 3.948,4.063 4.49,4.292 0.542,0.229 10 false 1 4.656,0.802 4.948,1.146 0.292,0.344 10 false 5*1, 10*2 3.948,3.031 4.49,3.26 0.542,0.229 10 false 2 5.052,3.156 5.594,3.385 0.542,0.229 10 false 2 4.625,1.719 4.969,2.073 0.344,0.354 10 false 14*1, 21*2 3.948,0.344 4.49,0.573 0.542,0.229 10 false 6 5.042,3.646 5.583,3.875 0.542,0.229 10 false 5 3.958,0.823 4.5,1.052 0.542,0.229 10 false 5 3.906,1.313 4.448,1.542 0.542,0.229 10 false 13 3.896,1.802 4.438,2.031 0.542,0.229 10 false 14 3.958,3.521 4.5,3.75 0.542,0.229 10 false 3 5.031,4.177 5.573,4.406 0.542,0.229 10 false 3 5.01,7.073 5.552,7.302 0.542,0.229 10 false E1 5,6.604 5.542,6.833 0.542,0.229 10 false HSSR 5.01,6.125 5.552,6.354 0.542,0.229 10 false VC 5.01,5.656 5.552,5.885 0.542,0.229 10 false VSSR 6.594,4.177 6.823,4.385 0.229,0.208 10 false 1 5.781,6 6.292,6.417 0.51,0.417 10 false Vertical Sensor 5.417,6.948 6.583,7.177 1.167,0.229 10 false Horizontal Sensor 4.625,6.906 4.969,7.25 0.344,0.344 10 false 14*1, 21*2 4.646,5.969 4.958,6.333 0.313,0.365 10 false 5*1, 10*2 4.646,5.5 4.969,5.844 0.323,0.344 10 false 6*1, 22*2 0.208,7.344 1.698,7.583 1.49,0.24 10 false *1: for 16 Pin Connector 0.208,7.75 1.698,8.021 1.49,0.271 10 false *2: for 22 Pin Connector 4.656,0.323 4.979,0.667 0.323,0.344 10 false 6*1, 22*2 4.615,1.281 4.979,1.625 0.365,0.344 10 false 13*1, 11*2 4.625,6.448 4.99,6.792 0.365,0.344 10 false 13*1, 11*2

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK SEAT MEMORY SWITCH FUNCTION
a.

When any seat memory switch (M1 or M2) is pressed, check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

2.CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION

NG

GO TO FRONT POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

2.CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION
a.

Check the electrical remote control mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Electrical remote control mirror function is normal.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror cannot be Adjusted with Power Mirror Switch)

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Mirror L or Mirror R / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON OFF: Not memorized
ON: Memorized
-
Body Electrical > Mirror L > Data List
Tester Display
Mirror Memory No.1
Mirror Memory No.2
50003 225 5,6
Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON OFF: Not memorized
ON: Memorized
-
Body Electrical > Mirror R > Data List
Tester Display
Mirror Memory No.1
Mirror Memory No.2
50003 224 5,6

OK:

ON (Memorized) appears on the screen.


Result:
Proceed to
OK
NG



OK

4.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror Surface Position is not Memorized)

4.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation function on driver door mirror is not normal B
Memory and reactivation function on front passenger door mirror is not normal C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

5.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

C

7.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
5.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)
a.

Temporarily replace the outer rear view mirror assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MEMORY AND REACTIVATION FUNCTION
6.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

7.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
a.

Temporarily replace the outer rear view mirror assembly (front passenger door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK MEMORY AND REACTIVATION FUNCTION
8.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)