Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/ Occupant Classification System) › from 2021.02
RM33A0E _58 Vehicle Interior _065386 SEAT BELT _0327385 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) G

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the engine switch on (IG).


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.


c.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


d.

Start the engine.


e.

When the driver seat belt is not fastened and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds.


f.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 24 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 100 seconds and then illuminates.


g.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 2.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



b.

Fasten the driver seat belt.


c.

Turn the engine switch on (IG).


d.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.


e.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


f.

Start the engine.


g.

When the front passenger seat belt is not fastened and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds.


h.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 24 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 100 seconds and then illuminates.


i.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 3.INSPECT REAR SEAT BELT WARNING LIGHT

a.
B345486C02
2.281,1.677 2.281,1.375 false 1.698,1.667 1.698,1.375 false 1.125,1.667 1.125,1.375 false 0.167,0.156 0.479,0.313 0.313,0.156 10 false *1 1.063,1.729 1.375,1.885 0.313,0.156 10 false *a 1.635,1.74 1.948,1.896 0.313,0.156 10 false *b 2.24,1.719 2.552,1.875 0.313,0.156 10 false *c
*1 Rear Seat Belt Warning Light (Telltale Light Assembly)
*a LH
*b Center
*c RH


Check the state of the rear seat belt warning light on the telltale light assembly:

i.

Turn the engine switch off.


ii.

Turn the engine switch on (IG).


iii.

When a rear seat belt is not fastened, check that the rear seat belt warning light on the telltale light assembly is illuminated.


iv.

After 66 seconds, check that the rear seat belt warning light on the telltale light assembly turns off.


v.

When one of the rear seat belts is unfastened from being fastened, check that the rear seat belt warning light on the telltale light assembly illuminates.



Hide 4.INSPECT FRONT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>CUSTOMIZE PARAMETERS


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



b.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


c.

Start the engine.


d.

When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 24 seconds.


e.

After the seat belt warning buzzer in the combination meter assembly has been sounding for 24 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 100 seconds.


f.

Check that the seat belt warning buzzer in the combination meter assembly stops 124 seconds after it started sounding at an interval of 1.2 seconds.


g.

After the seat belt warning buzzer in the combination meter assembly stops and the vehicle is driven at approximately 20 km/h (12 mph) or more with the driver and front passenger seat belt fastened, when the driver or front passenger seat belt is unfastened, check that the buzzer sounds in the same pattern again.


h.

After the seat belt warning buzzer in the combination meter assembly stops, move the shift lever to R and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened, and check that the buzzer sounds in the same pattern again.


Hide 5.INSPECT REAR SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>CUSTOMIZE PARAMETERS


a.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


b.

Fasten the driver seat belt.


c.

Start the engine.


d.

Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the seat belt warning buzzer in the combination meter assembly sounds once.


e.

After the seat belt warning buzzer sounded once, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.


f.

After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 60 seconds.


g.

Check that the seat belt warning buzzer in the combination meter assembly stops 66 seconds after it started sounding at an interval of 1.2 seconds.


h.

After the seat belt warning buzzer in the combination meter assembly stops, turn the engine switch off, open and close either rear door and then start the engine. Drive the vehicle at approximately 20 km/h (12 mph) or more while a rear seat belt is not fastened and check that the buzzer sounds in the same pattern again.


i.

After the seat belt warning buzzer in the combination meter assembly stops, fasten a rear seat belt, drive the vehicle at approximately 20 km/h (12 mph) or more, unfasten the rear seat belt and check that the buzzer sounds in the same pattern again.


j.

After the seat belt warning buzzer in the combination meter assembly stops, stop the vehicle, move the shift lever to R and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds in the same pattern again.