Home › Engine / Hybrid System › A25A-FKS (COOLING) › FLOW SHUTTING VALVE (for ATF) › from 2021.02
RM33A0E _51 Engine / Hybrid System _065346 A25A-FKS COOLING _0319573 FLOW SHUTTING VALVE(for ATF) A

A25A-FKS COOLING  FLOW SHUTTING VALVE(for ATF)  INSTALLATION  


PROCEDURE

Hide 16261G 1.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

a.

Install the flow shutting valve (No. 1 water by-pass hose) with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the flow shutting valve connector.


c.

Connect the flow shutting valve (No. 1 water by-pass hose) to the transmission oil cooler and slide the clip to secure it.

A402647C01
1.865,1.094 1.448,1.167 1.448,1.167 1.875,0.896 false 2.458,0.802 2.771,0.958 0.313,0.156 10 false *a 1.271,1.125 1.583,1.281 0.313,0.156 10 false *b 2.104,1.448 2.417,1.604 0.313,0.156 10 false *c 1.49,1.448 1.802,1.604 0.313,0.156 10 false *c
*a 2 to 7 mm (0.0787 to 0.276 in.) *b Paint Mark
*c 45° (Tabs of Clip Installation Area) - -


NOTICE:
·

Make sure to slide the flow shutting valve (No. 1 water by-pass hose) until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the flow shutting valve (No. 1 water by-pass hose) with the paint mark of the transmission oil cooler.

·

Make sure that the tabs of the clip are within the area shown in the illustration.




d.
A402649C01
0.729,3.385 0.854,3.865 0.854,3.865 0.979,3.396 false 0.771,3.885 1.083,4.042 0.313,0.156 10 false *a 1.771,2.958 2.083,3.125 0.313,0.167 10 false *b 1.76,3.604 2.073,3.76 0.313,0.156 10 false *b
*a Paint Mark
*b 45° (Tabs of Clip Installation Area)


Connect the flow shutting valve (No. 1 water by-pass hose) to the water outlet and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (No. 1 water by-pass hose until it contacts the hose) stopper of the water outlet.

·

Make sure to align the paint mark of the flow shutting valve (No. 1 water by-pass hose) with the paint mark of the water outlet.

·

Make sure that the tabs of the clip are within the area shown in the illustration.




e.

Engage the 2 clamps to connect the flow shutting valve (No. 1 water by-pass hose) and transmission breather hose to the hose clamp.


f.

Engage the 3 clamps to install the hose clamp.


g.

Engage the 3 clamps to install the transmission breather clamp.


Hide 74404A 2.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 28800 3.INSTALL BATTERY

Hide 5.ADD ENGINE COOLANT

Hide 53737B 7.INSTALL FRONT FENDER APRON SEAL LH

Hide 8.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53852K 10.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 11.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 12.INSTALL FRONT WHEEL LH