Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System) › from 2022.01
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329090 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

for 12 Pin Type


B472431E39
4.865,2.813 6.979,3.271 2.115,0.458 10 false Certification ECU (Smart Key ECU Assembly) 1.635,0.781 2.552,0.979 0.917,0.198 10 false DATA 1.823,1.438 2.74,1.635 0.917,0.198 10 false +5 0.24,2.99 2.896,3.51 2.656,0.521 10 false Electrical Key and Tire Pressure Monitoring System Receiver Assembly 0.24,2.823 0.615,3.01 0.375,0.188 10 false R127 5.177,1.448 6.094,1.646 0.917,0.198 10 false RCO 5.167,0.792 6.083,0.99 0.917,0.198 10 false RDAM 2.083,0.781 2.5,1.021 0.417,0.24 10 false 2 2.094,1.448 2.51,1.688 0.417,0.24 10 false 8 2.063,2.073 2.479,2.313 0.417,0.24 10 false 12 4.844,0.688 5.063,0.865 0.219,0.177 10 false 19 4.854,0.875 5.094,1.052 0.24,0.177 10 false R8 4.844,1.344 5.042,1.531 0.198,0.188 10 false 18 4.833,2 5.25,2.24 0.417,0.24 10 false 18 4.813,2.177 5.115,2.365 0.302,0.188 10 false K62 5.177,2.188 5.594,2.427 0.417,0.24 10 false E 1.698,2.156 2.042,2.344 0.344,0.188 10 false GND 4.854,1.521 5.063,1.719 0.208,0.198 10 false R8 6.281,1.208 7.156,1.406 0.875,0.198 10 false IC 5.865,0.365 6.781,0.563 0.917,0.198 10 false 12 V


for 5 Pin Type


B462039E03
1.583,0.75 2.198,0.948 0.615,0.198 10 false DATA 1.792,1.417 2.104,1.615 0.313,0.198 10 false +5 1.667,2.167 2.125,2.365 0.458,0.198 10 false GND 2.094,0.76 2.25,0.958 0.156,0.198 10 false 5 2.094,1.406 2.25,1.604 0.156,0.198 10 false 4 2.094,2.052 2.25,2.25 0.156,0.198 10 false 1 4.833,0.656 5.146,0.854 0.313,0.198 10 false 19 4.833,1.313 5.146,1.51 0.313,0.198 10 false 18 4.844,1.969 5.156,2.167 0.313,0.198 10 false 18 4.844,1.521 5.156,1.719 0.313,0.198 10 false R8 4.844,0.865 5.156,1.063 0.313,0.198 10 false R8 4.802,2.177 5.26,2.375 0.458,0.198 10 false K62 5.188,2.177 5.344,2.375 0.156,0.198 10 false E 5.188,1.406 5.646,1.604 0.458,0.198 10 false RCO 5.177,0.76 5.792,0.958 0.615,0.198 10 false RDAM 5.885,0.354 6.5,0.552 0.615,0.198 10 false 12 V 6.271,1.167 6.583,1.365 0.313,0.198 10 false IC 0.375,2.813 0.833,3.01 0.458,0.198 10 false R14 0.385,2.969 2.156,3.458 1.771,0.49 10 false Smart Door Control Receiver Assembly 5.125,2.823 6.646,3.281 1.521,0.458 10 false Certification ECU (Smart Key ECU Assembly)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing or inspecting the electrical key and tire pressure monitoring system receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the electrical key and tire pressure monitoring system receiver assembly, the performance of the entry function and wireless function may be affected.

·

This DTC is not stored within 10 seconds of the engine switch being turned from on (IG) to off.

·

Make sure that there are no electrical key transmitter sub-assemblies in the vehicle.

·

When replacing the electrical key and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.*

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

for 12 Pin Type


·

If the electrical key and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs to the electrical key and tire pressure monitoring system receiver assembly.*

for 12 Pin Type




PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the R127*1 or R14*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B440804C16
3.229,0.323 3.615,0.583 0.385,0.26 4.49,0.302 4.875,0.563 0.385,0.26 3.896,1.438 3.938,2.073 3.938,2.073 4.083,2.073 false 3.813,1.427 3.896,2.448 3.896,2.448 4.042,2.448 false 5.208,1.448 5.25,2.083 5.25,2.083 5.396,2.083 false 3.333,0.375 3.792,0.573 0.458,0.198 10 false R8 4.563,0.354 5.021,0.552 0.458,0.198 10 false K62 4.135,2.01 4.594,2.208 0.458,0.198 10 false RCO 4.125,2.396 4.677,2.552 0.552,0.156 10 false RDAM 5.438,2.031 5.99,2.188 0.552,0.156 10 false E 0.26,0.167 0.719,0.365 0.458,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
K62-18 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
R8-19 (RDAM) - K62-18 (E) Always 11 to 14 V
R8-18 (RCO) - K62-18 (E) Always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals



Result:
Result Proceed to
OK (for 12 Pin Type) A
OK (for 5 Pin Type) B
NG C



A

REPLACE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

B

C

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-19 (RDAM) - R127-2 (DATA)*1
R8-19 (RDAM) - R14-5 (DATA)*2
Always Below 1 Ω
R8-18 (RCO) - R127-8 (+5)*1
R8-18 (RCO) - R14-4 (+5)*2
Always Below 1 Ω
R127-12 (GND) - Body ground*1
R14-1 (GND) - Body ground*2
Always Below 1 Ω
R127-2 (DATA) or R8-19 (RDAM) - Other terminals and body ground*1
R14-5 (DATA) or R8-19 (RDAM) - Other terminals and body ground*2
Always 10 kΩ or higher
R127-8 (+5) or R8-18 (RCO) - Other terminals and body ground*1
R14-4 (+5) or R8-18 (RCO) - Other terminals and body ground*2
Always 10 kΩ or higher


*1: for 12 Pin Type

*2: for 5 Pin Type



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Click here


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR