Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System) › from 2022.01
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329090 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

When the wireless operation of the door lock function does not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the electrical key and tire pressure monitoring system receiver assembly and certification ECU (smart key ECU assembly) (the line used for wireless operations): or 2) the electrical key transmitter sub-assembly. If the wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the wireless function between the electrical key and tire pressure monitoring system receiver assembly and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B508205E04
0.885,0.573 2.115,0.813 1.229,0.24 10 false to IG1-NO. 1 Relay 1.208,1.26 2.104,1.49 0.896,0.229 10 false to ACC Relay 1.292,1.948 2.135,2.177 0.844,0.229 10 false from Battery 2.875,2.125 3.333,2.323 0.458,0.198 10 false AM2 3.698,0.417 3.938,0.604 0.24,0.188 10 false 17 4.021,0.625 4.635,0.823 0.615,0.198 10 false IG1D 4.031,1.302 4.646,1.5 0.615,0.198 10 false ACCD 3.677,1.323 4.135,1.521 0.458,0.198 10 false K62 3.698,1.104 3.948,1.292 0.25,0.188 10 false 16 3.75,1.781 4.063,1.979 0.313,0.198 10 false 4 3.667,2 4.125,2.198 0.458,0.198 10 false K62 4.021,1.99 4.333,2.188 0.313,0.198 10 false +B 1.552,3.865 1.865,4.063 0.313,0.198 10 false +5 1.354,3.208 1.969,3.406 0.615,0.198 10 false DATE 1.427,4.604 1.792,4.781 0.365,0.177 10 false GND 1.802,3.875 1.958,4.073 0.156,0.198 10 false 8 1.792,3.208 1.948,3.406 0.156,0.198 10 false 2 1.792,4.49 2.104,4.688 0.313,0.198 10 false 12 3.719,3.958 3.979,4.167 0.26,0.208 10 false R8 3.708,3.292 3.969,3.479 0.26,0.188 10 false R8 3.656,4.594 4,4.781 0.344,0.188 10 false K62 3.677,4.375 3.99,4.573 0.313,0.198 10 false 18 3.698,3.771 4.01,3.969 0.313,0.198 10 false 18 3.698,3.094 4.01,3.292 0.313,0.198 10 false 19 4.021,3.865 4.479,4.063 0.458,0.198 10 false RCO 4.031,3.167 4.646,3.365 0.615,0.198 10 false RDAM 4.031,4.594 4.188,4.792 0.156,0.198 10 false E 5.469,3.281 7.125,3.948 1.656,0.667 10 false Main Body ECU (Multiplex Network Body ECU) 3.948,5.625 5.479,6.281 1.531,0.656 10 false Certification ECU (Smart Key ECU Assembly) 0.125,5.24 0.51,5.417 0.385,0.177 10 false R127 0.115,5.385 2.802,6.094 2.688,0.708 10 false Electrical Key and Tire Pressure Monitoring System Receiver Assembly 0.594,6.292 2.323,6.49 1.729,0.198 10 false : CAN Communication Line 4.646,2.76 5.26,2.958 0.615,0.198 10 false 12 V 5.042,3.604 5.354,3.802 0.313,0.198 10 false IC 3.677,0.635 4.135,0.833 0.458,0.198 10 false K62

CAUTION / NOTICE / HINT

NOTICE:
·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock tuner circuit malfunction) is not output

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".

·

Electrical key and tire pressure monitoring system receiver assembly has a constant voltage (5 V) supply circuit connected to terminal "+5".

·

When replacing the electrical key and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

If the electrical key and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs to the electrical key and tire pressure monitoring system receiver assembly.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


OK:

Power door lock control function operates properly.


Result:
Proceed to
OK
NG



OK

2.CHECK WIRELESS DOOR LOCK OPERATION

NG

2.CHECK WIRELESS DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check the wireless door lock control function.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)>OPERATION CHECK


OK:

Wireless door lock control function operates properly.


Result:
Proceed to
OK
NG



OK

3.CHECK TRANSMITTER BATTERY

NG

5.CHECK WAVE ENVIRONMENT
3.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST




Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)

Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the electrical key and tire pressure monitoring system receiver assembly and perform a wireless operation check.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the electrical key and tire pressure monitoring system receiver assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




OK:

Wireless function operates properly.


Result:
Proceed to
OK
NG



OK

END (AFFECTED BY WAVE INTERFERENCE)

NG

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.


f.

Measure the voltage while checking the Data List on the GTS.

B416786C34
2,0.417 2.417,0.667 0.417,0.25 3.25,0.406 3.667,0.656 0.417,0.25 4.5,0.417 4.917,0.667 0.417,0.25 3.958,2.552 4.125,2.552 4.125,2.552 4.333,1.344 false 3.823,2.219 3.99,2.219 3.99,2.219 4.25,1.333 false 2.083,0.458 2.396,0.656 0.313,0.198 10 false A13 3.375,0.438 3.688,0.635 0.313,0.198 10 false R8 4.573,0.458 4.885,0.656 0.313,0.198 10 false K62 3.531,2.479 4.146,2.677 0.615,0.198 10 false ACCD 3.448,2.135 4.063,2.333 0.615,0.198 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Condition Specified Condition
K62-17 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
K62-16 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) 9 V or higher
Engine switch on (IG) 9 V or higher



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.READ VALUE USING GTS (ACC SW, IG SW)
a.

Enter the following menus: Body Electrical / Main Body / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Engine switch on (ACC) signal OFF or ON OFF: Engine switch off
ON: Engine switch on (ACC)
-
IG SW Engine switch on (IG) signal OFF or ON OFF: Engine switch off or on (ACC)
ON: Engine switch on (IG)
-
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

8.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R127 electrical key and tire pressure monitoring system receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-18 (RCO) - R127-8 (+5) Always Below 1 Ω
R8-19 (RDAM) - R127-2 (DATE) Always Below 1 Ω
R8-18 (RCO) or R127-8 (+5) - Body ground Always 10 kΩ or higher
R8-19 (RDAM) or R127-2 (DATE) - Body ground Always 10 kΩ or higher
R127-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY
a.
B472437C08
1.51,0.208 1.896,0.448 0.385,0.24 1.875,1.063 1.875,0.896 1.875,0.896 2.49,0.896 false 1,1.75 1.333,1.75 1.333,1.75 1.333,1.333 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.552,0.229 1.917,0.406 0.365,0.177 10 false R127 2.521,0.813 2.958,1.063 0.438,0.25 10 false DATA 0.667,1.656 1.125,1.854 0.458,0.198 10 false GND
*a Component with harness connected
(Electrical Key and Tire Pressure Monitoring System Receiver Assembly)


Measure the resistance according to the value(s) in the table below.


b.

Reconnect the R8 certification ECU (smart key ECU assembly) connector.


c.

Check for pulses according to the value(s) in the table below.

Standard Pulses:
Tester Connection Condition Specified Condition
R127-2 (DATE) - R127-12 (GND) Procedure:
1.

Turn engine switch off

2.

Lock all doors

3.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

4.

Press lock or unlock switch of electrical key transmitter sub-assembly


Pulse generation



Result:
Proceed to
OK
NG



OK

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B472437C09
1.531,0.188 1.875,0.448 0.344,0.26 0.938,1.729 1.354,1.729 1.354,1.729 1.354,1.313 false 2.458,1.729 1.875,1.729 1.875,1.729 1.875,1.313 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.542,0.198 1.906,0.385 0.365,0.188 10 false R127 0.604,1.635 1.063,1.833 0.458,0.198 10 false GND 2.5,1.635 2.813,1.833 0.313,0.198 10 false +5
*a Component with harness connected
(Electrical Key and Tire Pressure Monitoring System Receiver Assembly)


Check for pulses according to the value(s) in the table below.

Standard Pulses:
Tester Connection Condition Specified Condition
R127-8 (+5) - R127-12 (GND) Procedure:
1.

Turn engine switch off

2.

2. Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

3.

Press lock or unlock switch of electrical key transmitter sub-assembly


Pulse generation



Result:
Proceed to
OK
NG



OK

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
12.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock operation.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock function operates properly.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)