CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD | *B | for RHD |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | - | Ground | Always | Below 1 Ω | - |
| MB-30 (ACC) - Body ground | - | Input | ACC power supply | Engine switch on (ACC) | 11 to 14 V | ACC SW |
| Engine switch off | Below 1 V | |||||
| MB-31 (BECU) - Body ground | - | Input | Battery power supply | Always | 11 to 14 V | - |
| MB-32 (IG) - Body ground | - | Input | IG power supply | Engine switch on (IG) | 11 to 14 V | IG SW |
| Engine switch off | Below 1 V |
Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| 3C-29 (BZR) - Body ground | L - Body ground | Output | Wireless door lock buzzer output | Active Test Wireless Buzzer is OFF | Below 1 V | - |
| Active Test Wireless Buzzer is ON | Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| K62-4 (+B) - Body ground | W - Body ground | Input | Battery power supply | Always | 11 to 14 V | - |
| K62-18 (E) - Body ground | W-B - Body ground | - | Ground | Always | Below 1 Ω | - |
Reconnect the K62 certification ECU (smart key ECU assembly) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| R8-18 (RCO) - K62-18 (E) | B - W-B | Output | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Turn engine switch off 2.
Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area 3.
Press lock or unlock switch of electrical key transmitter sub-assembly |
Plus generation (See waveform 1) | - |
| R8-19 (RDAM) - K62-18 (E) | G - W-B | Input | Door control receiver communication circuit | Procedure:
1.
Turn engine switch off 2.
Lock all doors 3.
Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area 4.
Press lock or unlock switch of electrical key transmitter sub-assembly |
Plus generation (See waveform 2) | - |
| R8-20 (CSEL) - K62-18 (E) | BE - W-B | Output | Communication channel switching circuit | Procedure:
1.
Turn engine switch off 2.
Close all doors |
No pulse generation → Pulse generation | - |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester connection | R8-18 (RCO) - K62-18 (E) |
| Tool setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Turn engine switch off 2.
Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area 3.
Press lock or unlock switch of electrical key transmitter sub-assembly |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester connection | R8-19 (RDAM) - K62-18 (E) |
| Tool setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Turn engine switch off 2.
Lock all doors 3.
Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area 4.
Press lock or unlock switch of electrical key transmitter sub-assembly |