The door control receiver receives signals from the door control transmitter module set sub-assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.
When replacing the door control and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.*
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
*: for 12 Pin Type
If the door control and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs to the door control and tire pressure monitoring system receiver assembly.*
*: for 12 Pin Type
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Check the power door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Locked doors unlock.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the key reminder warning buzzer operates properly.
Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK
Key reminder warning buzzer operates properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When a known good registered door control transmitter module set sub-assembly is used, check that the wireless functions operate properly.
| Result | Proceed to |
|---|---|
| Wireless door lock/unlock function operates properly with a known good door control transmitter module set sub-assembly | A |
| Wireless door lock/unlock function does not operate | B |
A
B
Inspect the transmitter battery capacity.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Smart Entry and Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Smart Entry and Start System)>REPLACEMENT
Bring the door control transmitter module set sub-assembly near the door control receiver, and perform wireless operation check.
When the door control transmitter module set assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
Wireless functions operate properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Switch to self-diagnostic mode.
Check self-diagnostic mode.
| Result | Proceed to |
|---|---|
| Normal pattern (wireless door lock buzzer output pattern) is output | A |
| Unmatching recognition code is output | B |
| No diagnostic output | C |
A
B
C
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.
Recognition code can be registered.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Prepare a door control transmitter module set sub-assembly from another vehicle.
Press and hold a door control transmitter module set sub-assembly switch.
Check that an unmatching recognition code is output.
Unmatching recognition code is output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Front view of wire harness connector
(to Door Control Receiver) |
Disconnect the R128*1 or R16*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R128-12 (GND) - Body ground*1 | Always | Below 1 Ω |
| R16-1 (GND) - Body ground*2 | Always | Below 1 Ω |
*1: for 12 Pin Type
*2: for 5 Pin Type
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R128-7 (+B) - Body ground*1 | Always | 11 to 14 V |
| R16-5 (+B) - Body ground*2 | Always | 11 to 14 V |
*1: for 12 Pin Type
*2: for 5 Pin Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the R128*1 or R16*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R128-4 (RDA) - Body ground*1 | Procedure:
1.
Remove key from ignition key cylinder 2.
Close all doors 3.
Press lock or unlock switch of door control transmitter module set sub-assembly |
11 to 14 V → pulse generation |
| R16-2 (RDA) - Body ground*2 |
*1: for 12 Pin Type
*2: for 5 Pin Type
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 12 Pin Type) | B |
| NG (for 5 Pin Type) | C |
A
B
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System)>REMOVAL
C
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER (w/ Tire Pressure Warning System)>REMOVAL
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Disconnect the R128*1 or R16*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R128-4 (RDA) - K53-10 (RDA)*1 | Always | Below 1 Ω |
| R16-2 (RDA) - K53-10 (RDA)*2 | Always | Below 1 Ω |
| R128-5 (PRG) - K53-11 (PRG)*1 | Always | Below 1 Ω |
| R16-3 (PRG) - K53-11 (PRG)*2 | Always | Below 1 Ω |
| R128-4 (RDA) or K53-10 (RDA) - Other terminals and body ground*1 | Always | 10 kΩ or higher |
| R16-2 (RDA) or K53-10 (RDA) - Other terminals and body ground*2 | Always | 10 kΩ or higher |
| R128-5 (PRG) or K53-11 (PRG) - Other terminals and body ground*1 | Always | 10 kΩ or higher |
| R16-3 (PRG) or K53-11 (PRG) - Other terminals and body ground*2 | Always | 10 kΩ or higher |
*1: for 12 Pin Type
*2: for 5 Pin Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the door control receiver with a new or known good one.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the Registration procedure.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the doors can be locked and unlocked by the door control transmitter module set sub-assembly lock and unlock switches.
Doors can be locked and unlocked by the door control transmitter module set sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG