Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Tire pressure warning ECU and receiver

(w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function)

·

Occupant detection ECU

(w/ Occupant Classification System)

·

Brake actuator assembly

·

Rack and pinion power steering gear assembly

·

Steering sensor

·

Airbag sensor assembly

·

No. 2 CAN junction connector

·

No. 4 CAN junction connector

·

No. 3 junction connector



WIRING DIAGRAM

C385088E06
0.396,0.563 0.854,0.76 0.458,0.198 10 false 120 Ω 0.958,0.75 1.417,0.948 0.458,0.198 10 false CA2L 0.938,0.208 1.396,0.406 0.458,0.198 10 false CA2H 1.469,0.198 1.927,0.396 0.458,0.198 10 false 22 1.479,0.729 1.938,0.927 0.458,0.198 10 false 7 0.063,1.26 0.521,1.458 0.458,0.198 10 false K76 0.406,1.25 2.448,1.625 2.042,0.375 10 false Central Gateway ECU (Network Gateway ECU) 2.979,0.729 3.438,0.927 0.458,0.198 10 false 21 2.969,0.198 3.427,0.396 0.458,0.198 10 false 10 4.063,0.198 4.521,0.396 0.458,0.198 10 false 8 4.021,0.729 4.479,0.927 0.458,0.198 10 false 19 5.74,0.198 6.198,0.396 0.458,0.198 10 false 9 5.688,0.729 6.146,0.927 0.458,0.198 10 false 10 6.031,0.313 6.49,0.51 0.458,0.198 10 false CANH 6.031,0.844 6.49,1.042 0.458,0.198 10 false CANL 5.281,1.281 5.823,1.635 0.542,0.354 10 false R127 5.677,1.281 7.083,1.896 1.406,0.615 10 false Tire Pressure Warning ECU and Receiver*1 4.031,2.052 4.49,2.25 0.458,0.198 10 false 11 4.031,2.583 4.49,2.781 0.458,0.198 10 false 22 2.979,2.583 3.438,2.781 0.458,0.198 10 false 20 3.031,2.052 3.49,2.25 0.458,0.198 10 false 9 1.323,2.583 1.781,2.781 0.458,0.198 10 false 4 1.323,2.052 1.781,2.25 0.458,0.198 10 false 5 0.74,2.167 1.198,2.365 0.458,0.198 10 false CANH 0.771,2.708 1.229,2.906 0.458,0.198 10 false CANL 0.073,3.125 0.531,3.323 0.458,0.198 10 false a20 0.385,3.125 2.229,3.49 1.844,0.365 10 false Occupant Detection ECU*2 2.635,2.99 3.094,3.188 0.458,0.198 10 false R99 4.052,3.99 4.51,4.188 0.458,0.198 10 false 2 4.021,4.531 4.479,4.729 0.458,0.198 10 false 13 2.948,4.531 3.406,4.729 0.458,0.198 10 false 12 3,3.99 3.458,4.188 0.458,0.198 10 false 1 1.333,3.99 1.792,4.188 0.458,0.198 10 false 5 1.292,4.531 1.75,4.729 0.458,0.198 10 false 19 0.75,4.656 1.208,4.854 0.458,0.198 10 false CANL 0.729,4.115 1.188,4.313 0.458,0.198 10 false CANH 0.073,5.073 0.531,5.271 0.458,0.198 10 false A34 0.406,5.073 2.167,5.469 1.76,0.396 10 false Brake Actuator Assembly 4.073,4.917 4.531,5.115 0.458,0.198 10 false 4 4.031,5.448 4.49,5.646 0.458,0.198 10 false 15 5.698,5.448 6.156,5.646 0.458,0.198 10 false 11 5.688,4.917 6.146,5.115 0.458,0.198 10 false 10 6.031,5.021 6.49,5.219 0.458,0.198 10 false CANH 6.042,5.573 6.5,5.771 0.458,0.198 10 false CANL 4.792,5.99 5.25,6.188 0.458,0.198 10 false C71 5.115,5.99 7.146,6.563 2.031,0.573 10 false Rack and Pinion Power Steering Gear Assembly 2.948,5.448 3.406,5.646 0.458,0.198 10 false 16 3,4.917 3.458,5.115 0.458,0.198 10 false 5 2.51,5.844 2.969,6.042 0.458,0.198 10 false A67 2.823,5.844 5.01,6.104 2.188,0.26 10 false No. 2 CAN Junction Connector 2.948,6.198 3.406,6.396 0.458,0.198 10 false 6 2.833,6.417 3.292,6.615 0.458,0.198 10 false K127 2.906,6.729 3.365,6.927 0.458,0.198 10 false 17 2.823,6.948 3.281,7.146 0.458,0.198 10 false K127 2.948,7.198 3.406,7.396 0.458,0.198 10 false 7 2.833,7.417 3.292,7.615 0.458,0.198 10 false K127 2.885,7.719 3.344,7.917 0.458,0.198 10 false 18 2.833,7.948 3.292,8.146 0.458,0.198 10 false K127 4,7.938 4.458,8.135 0.458,0.198 10 false K128 4.063,7.729 4.521,7.927 0.458,0.198 10 false 17 4,7.406 4.458,7.604 0.458,0.198 10 false K128 4.115,7.198 4.573,7.396 0.458,0.198 10 false 6 2.667,8.25 4.802,8.479 2.135,0.229 10 false No. 4 CAN Junction Connector 5.521,7.823 5.979,8.021 0.458,0.198 10 false 27 5.521,7.292 5.979,7.49 0.458,0.198 10 false 26 5.833,7.313 6.292,7.51 0.458,0.198 10 false CANH 5.833,7.844 6.292,8.042 0.458,0.198 10 false CANL 5.208,8.323 5.667,8.521 0.458,0.198 10 false K73 5.542,8.323 7.125,8.604 1.583,0.281 10 false Airbag Sensor Assembly 0.094,8.323 0.552,8.521 0.458,0.198 10 false K71 1.333,7.823 1.792,8.021 0.458,0.198 10 false 8 1.333,7.292 1.792,7.49 0.458,0.198 10 false 3 0.74,7.417 1.198,7.615 0.458,0.198 10 false CANH 0.771,7.958 1.229,8.156 0.458,0.198 10 false CANL 2.979,2.99 4.698,3.417 1.719,0.427 10 false No. 3 Junction Connector 6.344,7.646 6.802,7.844 0.458,0.198 10 false 120 Ω 0.417,8.323 1.813,8.531 1.396,0.208 10 false Steering Sensor 5.167,1.927 6.958,2.604 1.792,0.677 10 false *1: w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function 5.167,3.052 7.042,3.51 1.875,0.458 10 false *2: w/ Occupant Classification System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the R99 No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C381591C40
1.333,1.333 1.76,1.615 0.427,0.281 4.427,1.427 4.427,0.646 4.427,0.646 4.594,0.646 true 4.438,1.729 4.438,2.135 4.438,2.135 4.604,2.135 true 4.271,1.427 4.271,0.458 4.271,0.458 4.438,0.458 true 3.927,1.417 3.927,0.135 3.927,0.135 4.094,0.135 true 4.26,1.719 4.26,2.313 4.26,2.313 4.427,2.313 true 3.927,1.708 3.927,2.656 3.927,2.656 4.094,2.656 true 4.104,1.417 4.104,0.302 4.104,0.302 4.271,0.302 true 4.094,1.708 4.094,2.479 4.094,2.479 4.26,2.479 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.427,1.396 1.854,1.688 0.427,0.292 10 false R99 4.177,0.063 4.792,0.354 0.615,0.292 10 false CANH*b 4.521,0.385 5.135,0.677 0.615,0.292 10 false CANH*d 4.667,0.563 5.281,0.854 0.615,0.292 10 false CANH*e 4.167,2.573 4.813,2.76 0.646,0.188 10 false CANL*b 4.51,2.24 5.125,2.531 0.615,0.292 10 false CANL*d 4.677,2.052 5.365,2.271 0.688,0.219 10 false CANL*e 4.344,2.406 4.958,2.698 0.615,0.292 10 false CANL*c 4.354,0.219 4.969,0.51 0.615,0.292 10 false CANH*c
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to Tire Pressure Warning ECU and Receiver
(w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function)
*c to Occupant Detection ECU
(w/ Occupant Classification System)
*d to Central Gateway ECU (Network Gateway ECU)
*e to No. 2 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R99-8 (CANH) - R99-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU and receiver*1
R99-9 (CANH) - R99-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Occupant detection ECU*2
R99-10 (CANH) - R99-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
R99-11 (CANH) - R99-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector


·

*1: w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function

·

*2: w/ Occupant Classification System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C372332C20
1.323,1.344 1.813,1.615 0.49,0.271 4.26,1.708 4.26,2.208 4.26,2.208 4.094,2.208 true 4.271,1.438 4.271,0.604 4.271,0.604 4.104,0.604 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.438,1.396 1.854,1.656 0.417,0.26 10 false R99 3.542,0.531 4.219,0.823 0.677,0.292 10 false CANH*b 3.552,2.125 4.229,2.417 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
R99-10 (CANH) - R99-21 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the R99 No. 3 junction connector.


b.

Disconnect the A67 No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C21
1.323,1.344 1.813,1.615 0.49,0.271 2.75,1.427 2.75,0.677 2.75,0.677 2.583,0.677 true 2.76,1.698 2.76,2.198 2.76,2.198 2.594,2.198 true 2.917,1.427 2.917,0.51 2.917,0.51 2.75,0.51 true 3.25,1.427 3.25,0.51 3.25,0.51 3.417,0.51 true 3.417,1.427 3.417,0.677 3.417,0.677 3.583,0.677 true 3.417,1.698 3.417,2.198 3.417,2.198 3.583,2.198 true 2.927,1.688 2.927,2.438 2.927,2.438 2.76,2.438 true 3.26,1.698 3.26,2.448 3.26,2.448 3.427,2.448 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.448,1.406 1.865,1.667 0.417,0.26 10 false A67 2.01,0.604 2.688,0.896 0.677,0.292 10 false CANH*b 2.042,2.125 2.719,2.417 0.677,0.292 10 false CANL*b 2.177,0.427 2.854,0.719 0.677,0.292 10 false CANH*c 3.479,0.427 4.156,0.719 0.677,0.292 10 false CANH*d 3.677,0.594 4.354,0.885 0.677,0.292 10 false CANH*e 2.219,2.365 2.896,2.656 0.677,0.292 10 false CANL*c 3.49,2.375 4.167,2.667 0.677,0.292 10 false CANL*d 3.656,2.104 4.333,2.313 0.677,0.208 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Brake Actuator Assembly
*c to No. 3 Junction Connector *d to Rack and Pinion Power Steering Gear Assembly
*e to No. 4 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - A67-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly
A67-2 (CANH) - A67-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 junction connector
A67-4 (CANH) - A67-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rack and pinion power steering gear assembly
A67-5 (CANH) - A67-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 3 junction connector) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the A67 No. 2 CAN junction connector.


b.

Disconnect the K128 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C19
1.323,1.344 1.813,1.615 0.49,0.271 3.583,1.427 3.583,0.583 3.583,0.583 3.396,0.583 true 3.594,1.708 3.594,2.167 3.594,2.167 3.406,2.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K128 2.844,0.5 3.521,0.792 0.677,0.292 10 false CANH*b 2.854,2.083 3.531,2.375 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K128-6 (CANH) - K128-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Airbag sensor assembly



Result:
Result
OK
NG



OK

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

NG

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the K128 No. 4 CAN junction connector.


b.

Disconnect the K127 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C22
1.323,1.344 1.813,1.615 0.49,0.271 3.583,1.427 3.583,0.677 3.583,0.677 3.417,0.677 true 3.594,1.698 3.594,2.198 3.594,2.198 3.427,2.198 true 3.76,1.427 3.76,0.677 3.76,0.677 3.927,0.677 true 3.76,1.698 3.76,2.198 3.76,2.198 3.927,2.198 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.406,1.406 1.823,1.667 0.417,0.26 10 false K127 2.854,0.594 3.531,0.885 0.677,0.292 10 false CANH*b 2.875,2.125 3.552,2.417 0.677,0.292 10 false CANL*b 4,0.594 4.677,0.885 0.677,0.292 10 false CANH*c 4.01,2.115 4.688,2.406 0.677,0.292 10 false CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Steering Sensor - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K127-6 (CANH) - K127-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
K127-7 (CANH) - K127-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor



Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
6.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the K73 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

C372332C19
1.323,1.344 1.813,1.615 0.49,0.271 3.583,1.427 3.583,0.583 3.583,0.583 3.396,0.583 true 3.594,1.708 3.594,2.167 3.594,2.167 3.406,2.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K128 2.844,0.5 3.521,0.792 0.677,0.292 10 false CANH*b 2.854,2.083 3.531,2.375 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly


Standard Resistance:
Tester Connection Condition Specified Condition
K128-6 (CANH) - K128-17 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

7.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C365212C15
1.5,0.083 1.885,0.313 0.385,0.229 1.146,0.469 1.313,0.469 1.313,0.469 1.313,0.969 true 1.167,1.719 1.333,1.719 1.333,1.719 1.333,1.135 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.573,0.115 2.01,0.365 0.438,0.25 10 false K76 0.75,0.396 1.188,0.646 0.438,0.25 10 false CA2L 0.76,1.646 1.198,1.896 0.438,0.25 10 false CA2H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K76-22 (CA2H) - K76-7 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR