Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › 2017.09–2019.02
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319337 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of brake actuator assembly
1.

Bleed air

2.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

3.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)for Initialization
(Click here)for Calibration
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the power switch is first turned on (IG) (Click here)

CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 47070 1.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

Hide 2.REMOVE FRONT WHEEL RH

Hide 48820B 3.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


Hide 4.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C377724C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C377726C01
2.479,1.385 2.208,1.385 2.208,1.385 2.031,1.083 true 0.979,1.708 1.271,1.708 1.271,1.708 1.458,1.51 true 0.625,1.198 1.104,1.198 true 0.729,0.677 1.01,0.677 1.01,0.677 1.302,1.021 true 0.958,0.344 1.208,0.344 1.208,0.344 1.5,0.854 true 2.333,0.292 2,0.292 2,0.292 1.677,0.75 true 2.5,1.302 2.667,1.469 0.167,0.167 10 true *a 0.792,1.625 0.979,1.792 0.188,0.167 10 true *b 0.438,1.115 0.625,1.281 0.188,0.167 10 true *c 0.552,0.594 0.729,0.76 0.177,0.167 10 true *d 0.781,0.271 0.948,0.438 0.167,0.167 10 true *e 2.333,0.208 2.5,0.385 0.167,0.177 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


c.
C377727

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.
C372674C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the vehicle body as shown in the illustration.


e.
C377732

Remove the 2 bolts.

HINT:

Insert the tool from the bottom of the vehicle.



f.
C377733

Remove the nut.


g.

Remove the brake actuator with bracket as shown in the illustration.

C381946

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44510 5.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C377734

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44546A 6.REMOVE BRAKE ACTUATOR BOLT CUSHION

a.
C377735C01
0.885,0.896 1.094,0.896 false 1.625,0.229 1.958,0.229 false 2.573,0.26 2.781,0.26 false 2.073,1.354 2.333,1.354 false 3.229,0.76 3.229,0.438 false 0.51,0.708 0.51,0.385 0.51,0.385 0.708,0.385 false 1.125,0.823 1.438,0.979 0.313,0.156 10 false *1 2.417,0.188 2.729,0.344 0.313,0.156 10 false *2 1.469,0.156 1.781,0.313 0.313,0.156 10 false *1 2.365,1.281 2.677,1.438 0.313,0.156 10 false *2 3.167,0.76 3.375,0.969 0.208,0.208 10 false *1 0.74,0.313 1.052,0.469 0.313,0.156 10 false *2
*1 Brake Actuator Case Collar
*2 Brake Actuator Bolt Cushion


Remove the 3 brake actuator case collars from the brake actuator bolt cushions.


b.

Remove the 3 brake actuator bolt cushions from the brake actuator bracket assembly.