Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2017.09–2018.04
RM33C0E _53 Suspension _065438 FRONT SUSPENSION _0334228 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 55708 2.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 48810 3.SEPARATE FRONT STABILIZER LINK ASSEMBLY

a.
C388456

Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 89543 4.SEPARATE FRONT SPEED SENSOR

a.
C370084

Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



Hide 48609E 5.LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C370087

Loosen the front support to front shock absorber nut.

CAUTION:
C378903

·

Only loosen the front support to front shock absorber nut if the front shock absorber with coil spring needs to be disassembled.

·

Only loosen the front support to front shock absorber nut, do not remove it.

·

If the front support to front shock absorber nut is removed with the front coil spring under tension, components of the front shock absorber with coil spring may fly off.




Hide 6.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C370085C01
2.156,1.344 2.813,1.344 true 0.615,2.271 0.708,2.271 0.708,2.271 1.281,2.146 false 2.854,1.26 3.167,1.417 0.313,0.156 10 false *a 0.448,2.188 0.76,2.344 0.313,0.156 10 false *b
*a Wooden Block
*b Jack
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

NOTICE:

Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.



b.
C370086

Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Use wire or an equivalent tool to hang the separated steering knuckle.




c.
C370088

Remove the 3 nuts and front shock absorber with coil spring.


Hide 48609E 7.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00051  
09727-30022  (09727-00010, 09727-00031)


b.

Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·
C322989

Make sure that the hooks are securely attached to the coil spring.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C370089

Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C312080

Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




c.

Install the stopper pins to the hooks of SST.

CAUTION:
C322990

·

Make sure that the stopper pins are installed securely.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




d.
C370090C01
0.625,0.813 0.625,1 0.625,1 1.156,1 true 1.563,1.135 2.958,1.135 true 0.344,0.813 0.875,0.813 false 1.417,1.302 2.76,1.302 2.76,1.302 2.76,1.135 true 0.188,0.729 0.5,0.885 0.313,0.156 10 false *a 3,1.052 3.313,1.208 0.313,0.156 10 false SST
*a Vehicle Nut


Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST
09727-30022  (09727-00090, 09727-00100)


e.

Using SST, compress the coil spring.

CAUTION:
·
C370091

If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C370092

Do not compress the coil spring to the point where the coils touch each other.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C370093

Do not use an impact wrench.

·

If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.

·
C370094N01
0.667,3.125 1.781,3.125 true 0.354,3.052 0.813,3.25 0.458,0.198 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.



SST
09727-00110  


f.

Check that the coil spring has become detached, and then remove the front support to front shock absorber nut.

CAUTION:
C370095

·

Do not remove the front support to front shock absorber nut while the coil spring is under tension.

·

If the front support to front shock absorber nut is removed with the coil spring under tension, components of the front shock absorber with coil spring may fly off, resulting in injury.




Hide 48609 8.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Remove the front suspension support sub-assembly from the front shock absorber assembly.


Hide 9.REMOVE STRUT MOUNTING BEARING WITH DUST COVER

a.
C370016C01
1.813,1.406 1.594,1.906 1.594,1.906 1.25,1.417 true 0.479,1.115 0.563,1.115 0.563,1.115 1.156,1.385 false 0.333,1.042 0.646,1.198 0.313,0.156 10 false *1 1.542,1.938 1.854,2.094 0.313,0.156 10 false *a
*1 Front No. 1 Shock Absorber Dust Cover
*a Claw


Disengage the end of the front No. 1 shock absorber dust cover from the claws of the front shock absorber assembly.


b.

Remove the strut mounting bearing with dust cover from the front shock absorber assembly.


Hide 48157C 10.REMOVE FRONT UPPER COIL SPRING INSULATOR

a.
C365592

Remove the front upper coil spring insulator from the strut mounting bearing.


Hide 48619A 11.REMOVE STRUT MOUNTING BEARING

a.
C365593

Disengage the top end of the front No. 1 shock absorber dust cover to remove the strut mounting bearing from the shock absorber dust cover.


Hide 48132 12.REMOVE FRONT COIL SPRING

a.

Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48331C 13.REMOVE FRONT SPRING BUMPER

a.

Remove the front spring bumper from the front shock absorber assembly.


Hide 48158C 14.REMOVE FRONT LOWER COIL SPRING INSULATOR

a.

Remove the front lower coil spring insulator from the front shock absorber assembly.


Hide 48691C 15.REMOVE SUSPENSION TOWER DAMPER (w/ Suspension Tower Damper)

a.
C388457

Remove the bolt and suspension tower damper from the front shock absorber assembly.


Hide 48520 16.REMOVE FRONT SHOCK ABSORBER ASSEMBLY