Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD)
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319337 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light blinks (red) when the power switch is turned on after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44546A 1.INSTALL BRAKE ACTUATOR BOLT CUSHION

a.

Install the 3 brake actuator bolt cushions to the brake actuator bracket assembly.


b.

Install the 3 brake actuator case collars to the brake actuator bolt cushions.

NOTICE:

Make sure that the brake actuator case collars are in full contact with the brake actuator bolt cushions.



Hide 44510 2.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 3.INSTALL BRAKE ACTUATOR WITH BRACKET

a.

Temporarily install the brake actuator with bracket to the vehicle body as shown in the illustration.

C381947

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.
C377736N01
2.25,1.438 2.375,1.625 0.125,0.188 10 true 1 1.01,0.271 1.135,0.458 0.125,0.188 10 true 2 0.677,1.448 0.802,1.635 0.125,0.188 10 true 3

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Install the 2 bolts from the bottom of the vehicle.



c.
C381948C01
0.948,1.104 1.354,1.104 true 1.938,0.771 2.427,0.771 true 2.427,0.677 2.615,0.865 0.188,0.188 10 true *a 0.75,1.021 0.938,1.198 0.188,0.177 10 true *b
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly


Temporarily tighten the 2 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.
C381949C01
2.865,2.917 2.708,2.917 2.708,2.917 2.708,2.667 false 1.781,2.948 2.094,3.104 0.313,0.156 10 false *a 2.885,2.833 3.198,2.99 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




e.
C381950C01
1.208,0.573 1.635,0.573 true 1.021,0.49 1.208,0.677 0.188,0.188 10 true *a
*a To Front Wheel Cylinder Assembly LH


Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




f.
C381951C01
2.844,2.906 2.698,2.906 2.698,2.906 2.698,2.667 false 1.802,2.948 2.115,3.104 0.313,0.156 10 false *a 2.865,2.833 3.177,2.99 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




g.
C381952C01
1.073,0.635 1.469,0.635 true 0.896,0.542 1.073,0.719 0.177,0.177 10 true *a
*a To Rear Wheel Cylinder Assembly RH


Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




h.
C381953C01
2.844,2.927 2.698,2.927 2.698,2.927 2.698,2.667 false 1.771,2.958 2.083,3.115 0.313,0.156 10 false *a 2.875,2.854 3.188,3.01 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




i.
C381954C01
0.792,1.188 1.083,1.188 1.083,1.188 1.167,0.854 true 1.719,1.115 1.51,1.115 1.51,1.115 1.354,0.781 true 0.604,1.104 0.792,1.271 0.188,0.167 10 true *a 1.74,1.042 1.927,1.208 0.188,0.167 10 true *b
*a To Front Wheel Cylinder Assembly RH
*b To Rear Wheel Cylinder Assembly LH


Temporarily tighten the 2 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




j.
C381955C01
2.854,2.927 2.698,2.927 2.698,2.927 2.698,2.667 false 1.781,2.958 2.094,3.115 0.313,0.156 10 false *a 2.885,2.854 3.198,3.01 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




k.
C377725C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 48820B 4.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


Hide 5.INSTALL FRONT WHEEL RH

Hide 47070 6.INSTALL BRAKE BOOSTER PUMP ASSEMBLY