Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for LHD)
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319339 BRAKE PEDAL STROKE SENSOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for LHD)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



a.

When installing a new brake pedal stroke sensor assembly:

NOTICE:

Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.


i.
C376560C01
1.146,0.719 1.417,0.719 true 2.688,0.844 2.688,1.042 2.688,1.042 2.875,1.042 true 2.552,0.625 2.552,0.375 2.552,0.375 2.75,0.375 true 2.75,0.292 2.917,0.458 0.167,0.167 10 true *a 2.885,0.958 3.052,1.125 0.167,0.167 10 true *b 0.979,0.646 1.146,0.813 0.167,0.167 10 true *c
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove
*c Brake Pedal Stroke Sensor Assembly Lever Set Pin


Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.


iii.

Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin.


iv.

Remove the broken lever set pin.



b.

When reusing the brake pedal stroke sensor assembly:

i.
C376561C01
2.813,1.042 2.646,1.042 2.646,1.042 2.646,0.844 true 2.729,0.344 2.552,0.344 2.552,0.344 2.552,0.625 true 2.729,0.26 2.896,0.427 0.167,0.167 10 true *a 2.823,0.969 3,1.125 0.177,0.156 10 true *b
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove


Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 nuts.

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.


a.

Connect the GTS to the DLC3 with the power switch off.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

e.
C376563

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



f.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



g.

Turn the GTS off and turn the power switch off.


h.

Disconnect the GTS from the DLC3.


Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 6. PERFORM INITIALIZATION AND CALIBRATION

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION